Your cart is empty.
Your cart is empty. #801 Gray Dektite Retrofit EPDM Flexible Pipe Flashing (RF801G)
-Flashing Base Diameter is 6-1/3" - Pipe Boot Fits 3/4" to 2-3/4" Outside Pipe Diameter
-Continuous Service Temperature Ranges of -58F to 239 F (EPDM)
-Easily Customize Pipe Boot Size on the Job Site With Shears or Heavy Scissors
-EPDM Rubber Boot with Flexible Base (Aluminum Collar) Seals Against Uneven Metal Roofing Easily
-Fasten Aluminum Collar To Metal Roof With Metal Roofing Screws Every 1-1/2"
-Where the Height of Pipe is Difficult to Reach or Existing Obstruction Blocks Top of Pipe;
-Flashing Can Be Cut Along the Seam and Resealed With Provided Clips
-If Trimmed and Installed Correctly, Pipe Flashing Will Not Break or Crack
-Reduces Building Maintenance Due To The Long Life of the Dektite Product
-Use for Stove Pipes, Chimneys, Plumbing, Heating, Air Conditioning, Electrical, and Exhaust Vents
-20 Year Manufacturer's Warranty Against Manufacturing Defects
Works with Metal Roof Pitches up to 10/12 (0 to 40 degrees)
On a Roof with a 10/12 to 12/12 Pitch (40 Degrees) Dektite Recommends You Use a Square Base Pipe Flashing Installed With The Base Tip Pointed Towards Roof Top. When Used With Deep Ribbed Profile Roofing Panels With 1-1/2" Deep Corrugation Or More, Consider Using Next Size Up That Will Accommodate The Same Diameter Pipe
Caution: This product is not rated for temperatures experienced by prolonged contact with a single wall chimney. Manufacturers Recommended Temperature Ranges Are Clearly Stated. Please Verify This Product Will Meet Specifications Of Your Installation Or Possible Product Damage May Occur
For single wall chimney applications consider using a High Temperature Silicone Flashing product that is rated for high temperature applications
David Miller
2025-08-07 11:48:01
It was very easy to modify and fit over the vent pipe. You still need the self tapping screws and silicon sealer. I recommend viewing the video before you begin the installation if you haven't done this before.
david
2025-07-30 15:55:33
Works great
Tyler
2025-07-19 18:59:14
I used it on a metal roof for a Electrical Mast and it worked great just make sure your cuts small. No room for error. But it's very low profile and looks good.
EXPEDITION
2025-07-12 10:12:04
Easy peasy worked like a champ. The Dektite Retrofit electrical mast boot fit perfectly and zipped closed after sizing, cutting and fitting. It will be tested from the Florida sun hopefully has some longetivty. No more ðŸ¿ï¸ in the attic !
Frank Ten
2025-06-18 21:11:07
This took care of the pipe I had to seal around on the roof as water was leaking into the soffit. Very well priced and easy to install. I used tar in a tube for the bottom with roofing nails and clear silicone for the top and the seam.
bob
2025-06-06 14:12:46
I used this to fix a sloppy contractor installation of A/C lines through the wall in my house. Easy to install and is robust enough to last a long time. I'd definitely recommend this.
David
2025-04-21 13:59:10
I wasn't sure about the size or if this was going to work but it has the feature of being adjustable by trimming off excess. Works like a champ
JOHN LARSEN
2025-02-09 09:44:25
Will surely make your roof leak. Garbage way of securing the 2 slip sides together after retrofitting. Also way too small only like half an inch of lippage to flash onto. No roofer would use this.
mike
2025-02-01 16:24:37
At first I thought it was a bit expensive but I can see why, it is solid and very well made, worked great!
A. Cooper
2025-01-24 11:32:53
I bought this for my electricity service stack on my house. I was able to split the boot and put it on the stack after cutting the top to the desired size for the stack. The rubber compound was very pliable yet tough. I had to use sidecutters to cut the top off the boot. (which is a good thing). I found the base to be a little smaller than I expected but it is also a smaller boot.
Recommended Products
