Your cart is empty.
Your cart is empty.Product Description
10AWG solar to XT60i cable
The 10AWG solar cable carries more current and is more conductive to provide a stable current to the device.
MOOKEERF cables are made of tinned copper wire to minimize power loss and increase charging efficiency.
The jacket is made of high-quality PVC material that is weather and UV resistant and heat resistant up to 105°C.
- 10 AWG Cable
- Tinned copper conductor
- PVC jacket
- Heat-resistant to 105°C
Tinned Copper
Good conductivity and keep the voltage stable.
Standard XT60i Connectors
The anti-reverse plug design prevents misconnections and provides better safety.
10AWG Wire
10AWG can carry higher currents, providing better current transfer and more stability. Our cable jackets are made of PVC and can withstand temperatures up to 105C. Voltage 600V.
Dehldog
2025-08-02 11:23:53
Haven't used it yet, but it looks solid and AWG 10 is best for my battery backup solar recharge.
Michael
2025-06-27 17:58:54
I bought these to use with my EcoFlow Delta 2 Max. The connector is the XT60i and EcoFlow uses the center pin to determine if you are plugging solar panels or a battery into the XT60 ports. I thought these would already be center pin connected to negative, but they were not. The center pin is not connected to anything. So, if you want to use these, to fool an EcoFlow solar generator into thinking your external battery is a solar panel, so you can get the full 15 amps the port allows for solar, then you need to connect the center pin to negative. Just make sure you don't use this connector with a vehicle's wiring, as 15 amps is too much current for most vehicle wiring. EcoFlow limits DC charging into the port to 7-8 amps. You can connect the center pin to positive and that will limit the port to the lower amps.
Linden
2025-06-16 20:36:28
These are nicely made cables that work well in connecting 2x EcoFlow NextGen Bifacial 220w panels to my Delta 3 Plus (D3P) solar generator. 25 feet gives a big improvement in flexibility of placement for the panels vs the short OEM cables. It’s also nice that these have the XT60i connectors that plug directly into the D3P. The MC4 connectors aren’t the easiest to unclip, but they aren’t too bad either. The OEM EcoFlow cables have squeeze tabs that work better to disconnect, so these cables could learn from that. My only other fault is that the rubber is a bit stiff and likes to twist when rolling it up. Overall they’re about what I expected. As far as electrical performance they work great because I’ve seen up to 209w out of a 220w panel, so there doesn’t seem to be a downside to using a 25’ power cable in my setup.
Kirby T.
2025-05-29 15:50:05
This works great for my Renology 100w panel charging up the River3 solar power station. Nice and heavy wire with the correct connection of the XT60i connection. I was pushing out 75+ watts from the solar panel into my device and did not over heat the wire.
Rob Lee
2025-05-25 12:33:39
Very happy with this item. Seems to be well made.
Luis C.
2025-04-24 19:21:54
Muy buen producto, cumple
Josiah L
2025-04-20 15:45:22
I used this with 1200 watts solar panels(over panel, as it will only take 500watts in each port) My ecoflow delta 2 max will charge very quickly with this setup!
JPS
2025-02-24 13:57:06
Have not set them up yet but my son has them and they are wonderful
Customer
2025-01-02 11:03:01
Nice cables and good quality, BUT the signal pin is NOT connected to anything. This only matters to some people, but I am one of them.
J. Kroell
2024-11-29 12:15:13
Yes it’s an XT60i connector but the most important thing that makes it such is not connected! The center pin is left all alone by itself, so the device you’re connecting to will assume this is a traditional XT60 cable and limit the charge. In my case my EcoFlow River 2 pro assumes it is an AC or non-solar DC connection and limits the input.Quick and easy fix if you have a soldering iron but doing so probably revokes any chance of returning if it’s faulty.Also, look at those solder joints!!! Oxidation already? Did you dip the stuff in a tub of salt water?Wires are decent CCA and appears to be true to AWG size.When you specifically sell this as a solar charging cable, PLEASE connect the center pin so devices can get all the juice possible. AKA jump the center pin to neg for solar, especially since the other connectors are MC4 (specifically for solar).
Recommended Products