Shopping Cart

Your cart is empty.

Your cart is empty.

Sporacingrts Metallic Heat Shield Heat Shroud - Aluminized Sleeving Compatible with Ultimate Heat Protection (with Hook and Loop Closure):L 71.65'' W:3.94''

4.7 (8) Write Review
Free shipping on orders over $29.99

$9.99

$ 4 .99 $4.99

In Stock
  • 【Product Size】The width is 3.94 inches and the length is 71.65 inches. Wrapping material, aluminum-plated back, thermal fiber wrap color, white bottom, temperature rating (Fahrenheit) 500 direct, wiring, braided hose, etc.
  • 【High-Quality Materials】The thermal zero aluminized heat sheath will help to keep what needs to stay cool, cool or the opposite. On one side we use the same thermal fiber material we use in out heat wrap and the flexible aluminum shielding material on the other side.
  • 【Fashion Design】Our thermal sheath is designed and produced here in the United States. We double stitched the seams and even finished the edges of the seams, so it won't look ugly and worn in your engine compartment. The heat shield is made of high-temperature resistant glass fiber fabric with an aluminized outer surface.
  • 【Convenient】With the added convenience of a hook & loop closure design along the open edges. Without the need of removing one end of connected wires, cables and hoses simply wrap Heat Shroud around whatever needs protection and close the edges.
  • 【After-Sales Service】:If you encounter any problems when you receive the item, please contact me in time, I will be happy to help you


Product Description

Metallic Heat Shield Heat Shroud

Metallic Heat Shield Heat Shroud

Premium Heat Shroud

Heat shroud sleeve aluminized sleeving is made of high-temperature resistant fiber glass fabric with an aluminized outer surface.

Metallic Heat Shield Heat Shroud

Wide Applications

Widely used in protecting spark plug wires, fuel line heat shield, starter heat shield, wiring, brake lines, intake tubes, pipes, battery cables, A/C hoses etc which need insulation

Metallic Heat Shield Heat Shroud

Double Stitched The Seams

We double stitched the seams and even finished the edges of the seams, so it won't look ugly and worn in your engine compartment.

Metallic Heat Shield Heat Shroud

Usages

Easy to Install

Aluminized heat shield sleeve is easy to install. Without removing one end of connected wires, cables and hoses, you just simply wrap the aluminized sleeving around wires, cables and hoses or whatever needs heat protection, and then close the edges, simple to oprate and done in seconds. Easy to cut to the length you desired and velcro around wire looms.

Metallic Heat Shield Heat Shroud

Xavier T. Le
2025-09-01 16:02:23
Cut this to spec and used inside engine bay
Car Guy
2025-08-21 10:42:34
Worked better than anything else I have tried on my 1966 Chevelle fuel line. It has greatly helped with eliminating vapor lock and is far easier to install than sleeve type of insulation.
Joe Consumer
2025-08-12 16:31:09
Used this to wrap some wiring on my Hummer H3 that is so close to the exhaust system that conventional split loom melts/deforms. This product works like a charm to keep my wiring cool. Easy to cut to length, install and secure. The length of the insulation I received was the 71" shown in the product title and not the shorter length shown in the description.
Brody
2025-08-06 17:42:09
product works fine. used to cover oil feed lines for turbo that runs right through exhaust header. lots of fiberglass floating around after installing it wear gloves and breathing mask.
Dennis
2025-04-29 14:06:33
This shielding works but cannot take direct exhaust contact. A portion touched against my exhaust and the shiny metal baked off of the fiberglass. The fiberglass then charred. Good product, but will not stand direct heat.Product update. Please see the attached photos of this shielding near exhaust. Notice how the foil has completely burned off. The fiberglass does hold up. When you install be sure to not let this come in direct contact with you exhaust.
vincent
2025-04-22 12:17:52
Cable now protected from headers!
Benjamin Smith
2025-01-15 14:59:35
Works as advertised.
Loonasea
2024-12-12 19:30:50
Extremely hard to work with unless what you're covering is perfectly straight. The stitching is pitiful, be very careful if you have to reposition the velcro because the stitching will immediately start to pull out .I ended up having to use an adhesive metal tape (like is used on HVAC systems) to hold it together. I was covering the heat bypass tube that goes to the EGR on my '90 Ranger, it has a couple curves in it and was VERY hard to cover.