Your cart is empty.
Your cart is empty.Product Description
TF Micro SD To SD Card Extension Cable Adapter Flexible Extender For Car GPS
Features:
100% Brand New and High Quality
Push-Push SD slot.
Support all size 16GB, 32GB 64GB 128GB SD / SDHC card.
Compatible with GPS, DVD, DVR, LED/LCD screen, or mobile phone Smartphone etc.
Total Length: 53.5cm Cable Lenght: 46cm
Material: Plastic+FFC
Quantity: 1 Pc
Net Weight: 20g
Where can use?
Convenient to test many SD memory-cards on any electronic device which supports MicroSD(TF) memory card,PDA,smart phones, MP3, MP4.Digital Camera ,GPS.
Also used as extender or Linker when your device has built-in Micro SD Memory Card Slot and you need to extend it outside to use Bigger SD Memory Card.
Steve_in_TN
2025-08-25 17:31:54
Hello All, It's Steve@HobbyADHD With Another Review!This product has been a great addition to my 3D printer. I haven't disconnected it since the day I received it and it's been working great. A must have if you need an adapter.Construction: Very sturdy. The cable is thick and the casing on the SD card slot is beefy.Fit: Solid connection.Usability: Works great on my 3D printer.Issues: NonePros: Works every time Solid constructionCons: NoneI would highly recommend this product if you have a 3D printer that uses microSD cards. It works perfectly and gives a needed SD card slot for my Anet A2 3D printer.
SmokinJoe
2025-07-27 18:37:28
Nothing much I can say other than I bought this to remote-mount a camera, but the camera doesn't recognize the SD Card with the extender in between. Camera works fine without it. And I can't even get my money back. Avoid.
R D. Grayson
2025-07-02 11:19:02
It saves me from wearing out the port on my 3D printer and lets me use the stack of older full-sized SD cards I had left over.
Christian.glahn
2025-06-29 12:21:13
This has a great quality build feel and I really like that. It works well for Raspberry Pi, only problem is that the microSD end is quite a bit longer than a standard SD, and this provides a lot of leverage which could damage the SD slot, if not handled properly.
leon jones
2025-05-23 09:21:05
Loses connection mid print, so unusable for my application.
Fast eddie
2025-05-19 16:09:56
WOW, if you have an Elegoo Neptune Pro 3, you need this adaptor. Had a hard time getting the micro sd card into the slot, dropped numerous times and had to use a flashlight to see the opening. Simple to install; plug the small end into micro sd card slot, run flat cable under the printer, using two (2) sided tape attach the boss end adjacent to the screen. Tips: make sure to use a 8 or 16 gig standard sd card. Attach opening of the SD card receptacle on edge of printer to allow removal of the card.
Kindle Customer
2025-05-05 19:55:57
It works, sort of. Connections won't click in positively so had to manuall hold the cable while using.
Neal W.
2025-04-20 15:09:41
The inherent issue of card not seen or not recognized when its plugged in permanently with cover is a pain in the kiester.... but it will do what you want if you power cycle the printer evey time you insert or take out a card .This is the same issue I have with sd card adapter on my laptop but I can pull the adapter easy enough.
Space_shelf8
2025-04-16 18:55:03
Works great with a Bambu 3D printer, which uses a micro SD card slot. Didn't want to repeatedly wear out the micro SD slot on the printer so got this. Also, it's much easier to use a full sized SD card vs the micro when transferring files. A great upgrade and good quality, no issues with connectivity after multiple prints. Would recommend!
Jacques
2025-04-07 13:02:24
prfait pour un bricoleur
Roy & Beth
2025-02-19 15:12:24
Bought this because my 3D printer has the micro SD card in the back and it's a pain to install and remove it. I plug this into the micro SD slot and then place it at a more convenient location. It didn't matter to me that it is micro SD to standard SD as being an adapter was not what I wanted it for. Saving my printer files on a micro SD or full size SD is irrelevant. I only wanted the convenience of bringing the slot to a better location.There is one downside though that prevented a 5 star review. And that is when you remove the SD card and reinsert it again, the card is not recognized. I have to power down the printer and power it back up again to recognize the newly inserted card. But that is less of a pain than reaching behind the printer to find the micro SD slot. So I'm still very happy with it.
J S
2025-01-03 17:33:55
Works good and its long enough to reach glove box from the radio
Jennifer Janes
2024-12-25 17:57:57
No issues, works like it should.Not much else needs to be said.
Recommended Products