Had an inch of fluffy snow this morning, so it was a perfect test of my new 24" snow pusher shovel. My driveway is 16' wide and 10' long and I was able to clear the driveway in 10 minutes with no lifting of snow involved. The curve of the shovel held the snow that piled up as I pushed it across the drive. At no time did any snow stick to the shovel surface. I realize that for heavier snows, it will be necessary to do the clearing in layers. For major storms, like earlier this week when 12" of heavy snow came down, I'll use the snow removal service. All in all, the Snowplow Snow Pusher is a very sturdy, easy to use snow removal tool. I never thought I would actually enjoy snow removal until I used it.Update: 2/14/25 - After a 4" snow, it rained, leaving a heavy, wet layer. The snow pusher could only move the snow maybe 2 feet before it piled up over the top. Since pushing any harder would have been hazardous to my health, my workaround was to push to the side in increments of a few feet. I was able to clear a narrow path from the front door to the mailbox. Even if I had my old gas powered snow blower, it would have stalled out or clogged trying to clear a wide path. The Snow Pusher is still a good buy.

Works great always. Light weight, but very sturdy. I also have a 48" snowplow which works great for light snow. However, it can be too much for me in heavy or deep snow. I got this 24" plow and it has handled anything Colorado snow has thrown at me so far.Overall, this is an excellent product.

I don't write reviews. But.....The Snowplow Shovel just arrived and so did the snow!It really does plow through the snow!At 5'5"....the 24" blade is the perfect size for me...plus it really is very light weight! It's surprisingly very sturdy too!Assembly was easy...but I did need to use a small cordless drill for the self- tapping screws.I started with about 3-4 inches of fluffy snow. Fast and easy clean up!Then the wet stuff came down.The shovel worked just as good!I even used it to swiftly clear the snow off the hood and roof of my car!(Not recommended...but it didn't scratch anything)In comparison to everyone else that was shoveling their smaller driveways.....this Plow Shovel definitely speeds up the job of snow removal a lot!!!I am super happy I found this product and read the reviews.Two thumbs up!! Five Stars across the board!

This is good at pushing snow, and for throwing snow forward when lifting. If you try to lift and turn you will lose your scooped snow. This is the "con" to this design if you only have 1-shovel, however I don't think this is a "con" because the design is to be a snow pusher, and in fresh snow this thing glides. In older crunchy snow I think you would find a different shaped design better, so you might end up owning multiple snow shovels if you are looking for the best quality of life.

This is a great shovel. I owned the 48” model when I lived in MN, and used it for more than a decade, and loved it. But in MN, you can go into any hardware store, and buy one of these already assembled, ready-to-go. Now I live in NC, and when I went to the store looking for a snow-shovel (which we rarely need), I just got confused looks. So I bought this 24” one on Amazon.There are a LOT of negative reviews, mostly complaining about assembly issues, or missing hardware. So let me set the record straight. YES you will need tools and some mechanical aptitude to assemble this shovel – so know that in advance. Why can’t the manufacturer make this clear in the description? Better yet, why can’t the manufacturer pre-drill pilot holes, and make this a lot easier for everyone? But having said that – it really is a high-quality, very sturdy shovel, and the included hardware is top-quality stainless.OK – here is what you need to know: First of all, the hardware is hiding. They stuff the bag of hardware into the cylindrical socket in the brace – where the handle inserts into – and where you would NEVER see it if you didn’t know to look there. As a guy who never reads instructions, I too was certain it had been shipped without hardware, until I noticed the sticker telling me where to look.Next – to assemble the blade to the brace, you will need TWO 7/16” wrenches, one for the bolt, and one for the Nylock nut. I used a 7/16” socket plus an open-end wrench. A crescent wrench or even a pliers can hold one end if that’s all you have handy. First get all the bolts assembled in their (pre-drilled) holes, but don’t tighten yet. Then go back and tighten-up the bolts across the blade, and finally the one on top. No need to really torque them down, just reasonable hand tighten so you don’t deform the plastic. (by the way this is REALLY high-quality plastic – incredibly tough and sturdy). This is the easy part.Finally – we get to what all the complaints are about: there are 3 self-drilling/tapping stainless screws which are intended to drill through the plastic brace, and then drill and thread into the thin steel tube of the handle, thus securing it to the blade assembly. There are no pilot-holes – you as the assembler, have to run these fasteners at the correct speed to drill through two different materials, and then not over-torque them and strip-out the screw in the handle. This is where everyone is complaining that you need a power screwdriver. Its true – no way you could do this with a hand screwdriver. In addition, while doing this drilling/tapping operation, you have to make sure the handle is fully inserted to the proper depth, AND the handle is rotated to the correct position. I’m an experienced machinist, yet I can completely understand why many would be hesitant with this step. If you have never used a fastener like this, you have no room for error – either it works for you the first time, or not. If you don’t have a pristine Phillips #2 head on your drill/driver, chances are that, even if you do everything perfectly, the screw can slip and get away from you while trying to drill into the side of a steel tube with no centerpunch, and go sideways. Moreover – once you finally drill through the steel tube of the handle, now the threaded portion engages, and with your drill still spinning at high-speed, the threads could rapidly hit bottom and strip-out the steel tube. Be careful. Take it slow. Or – better yet, pre-drill pilot holes with a 1/8” drill – then it is easy to thread the self- drilling/tapping screws in, even with a regular Phillips driver.With successful assembly, this shovel is great – I would give it 5-stars. But because of the assembly issues which are going to be a problem for many people, I have to subtract a star.

Great shovel. Works good and very durable. Highly recommend

I wish I would have bought one of these sooner. We moved this past summer and the driveway is larger than our last. With this shovel, I can clear out my driveway, walk path and back yard path quicker. The design keeps it flat to the ground so you don't have to "double shovel" the same areas. I would recommend this to anyone. My only complaint is that I didn't buy the 36' model. I would be done even quicker had I known how great this shovel is.

Great pusher shovel. Well made. Love the D handle. Ive used it 3 times in 2024.

It's good quality 👌🏼 but not for the price. I am not sure what I was thinking because you still have to push it with your human hands 💩 So far doing well after one winter of use. I'll keep updating the review overtime