Your cart is empty.
Your cart is empty.Product Description
Product Details
Operation Mode
- Poles : DPDT; Terminals : 6 Pins;Position:3 Position(ON/OFF/ON)
- This is a self-locking switch. When it is opened, the switch is energized
Voltage
- Rated Voltage and Current : AC 10A/125V 6A/250V
- This switch can use 12V
Size
Mounting Size: 26 x 21.5mm / 1.02" x 0.85" (L*W); Overall Size: 30 x 25 x 35mm / 1.2" x 1" x 1.4" (L*W*H)
A variety of switches are available
Customer
2025-08-25 18:57:28
Exactly what I needed for reversing an electric motor. Seems well built.I’d buy again if needed.
Gerald B.
2025-07-23 14:04:38
It's a nice switch.It works great.You don't get a video
Riceman00
2025-07-22 12:48:53
This switch works well and was used for auxiliary controls for an electric radiator fan.My only gripe is the lack of a provided wiring digram/pinout. The product pictures only show very specific applications. Because of this, I have removed one star, and have provided my own diagram.
Mark
2025-07-19 15:44:25
Used this to replace a fried forward/reverse on my sons has a battery powered 4 wheeler. I don't think the brand is a Power Wheels, I think it's a Kid Trax or something (It's branded Caterpillar, FWIW). I went with this switch instead of the Amazon recommended one that says "for Power Wheels" because this switch had the correct power ratings. I don't know if my son's 4-wheeler has a different power requirements or different wiring than Power Wheels but I wanted to replace with as close to the same as I could the old switch said "20A/125V 16A/250V" on the side so that's what I wanted to find. The only major difference is this switch is an on/off/on instead of the on/on it replaced.Installation was easy, just popped the wires with slide connectors off the old broken switch and connected them to the new switch. I haven't noticed any issues with the fact that this is a different type of switch and I can't imagine the switch failing because this one has an "off" in the middle.I think this switch is a good value; plus two switches means I have a backup in case the "high speed/low speed" switch fails (or maybe I just take that as a sign to find him a new 4-wheeler). My only "complaint" isn't really about this product, it's the fact that I spent a day searching every corner of the internet and could not find an On/On 6-pin DPDT rocker switch rated for 20A/125V and 16A/250V. Maybe that's more of a complaint for whoever made the 4-wheeler because it doesn't seem like a standard switch for that form factor.
Nate Finley
2025-06-20 17:34:50
The switches were a perfect replacement for my broken KCD2 switches used in my kid Trax shifter. I was hesitant since these are KCD4 switches and didn't know the difference but they were a perfect replacement.
ClarkE
2025-06-16 17:08:10
These switches replaced faulty switches that raise/lower stabilizers on our toy hauler.
JJPeach
2025-06-03 17:16:40
Look and works good
HowieZ
2025-05-27 17:15:23
I bought this to bi-amplify or use crossovers for a woofer/tweeter speaker. They work great, seem sturdy and are easy to plug in the 1/4" spade terminals. I was tricked by fact that terminals seem backwards to me, but perhaps that's normal for a switch like this. I had wired the crossovers to the I position and the bi-amp to the II spot. Turns out the terminals are on the opposite end of the rocker. I simply swapped the wires, so no big deal, but it threw me for a loop for sure. A wiring diagram and dimensions to cut a hole would have been nice, but we made it work.UPDATE to this review. After a few gigs, the switches have both stopped working 100%. I typically have to rocker them back and forth a bit, one pole is out most of the time, several times both poles. I'm isolating a woofer and tweeter and their respective crossovers. I'm using it to connect/disconnect two wires from bi-amplified, or two wires from the crossover. The center pins are positive for woofer and tweeter. Outer pins each positive for bi-amp on one end and xover on other. I switch to bi-amplify (no cable there) and back, and the mid/woofer comes back on. Some days it's the other way around. I can always move the speaker wire to the other jack and toggle the switch and one driver comes on as expected. I may buy another brand to try and swap them out. It's annoying having to pull them out from the shelf to rocker the switches a bit just to listen to music.Overall a good value and they work great. I'll buy these again if I do another similar project.
Blake
2025-04-24 16:02:28
Both switches failed within 2 weeks of install. One post melted off. Was rated higher amperage then the switch that was on the heater from factory.
Jeff Bosma
2025-04-12 17:48:46
Served the purpose it was purchased for.
S.Gélinas
2025-02-21 09:30:59
Utilisé sur un ventillateur 2 vitesse
Buyer
2025-01-30 16:57:06
works great
Larry Dee
2025-01-06 10:36:02
What I wanted was a toy forward gear and a reverse gear riding tractorWork great easy to installNext day delivery was on timeDriver followed delivery instructionsI was very pleased
Recommended Products