Your cart is empty.
Your cart is empty.Enhance your control with the UltraPro Add-on Switch with QuickFit™ and SimpleWire™. When paired with a smart switch, dimmer or fan control, the hardwired device completes multi-switch systems. It works seamlessly with smart devices from UltraPro, Jasco, Enbrighten and Honeywell. Wirelessly operate and schedule indoor or outdoor fixtures from up to five locations for effortless management of your home.
BV
2025-09-06 09:13:36
I bought this switch in addition to the GE Zwave switch - because I wanted to see which one is better - only to realize both look identical and without the GE logo on the other, its difficult to tell them apart! Then I found out, both are manufactured by JASCO!!So from quality perspective this switch is no different from the GE Switch review. Some of these will be exact replica of my other review.PackagingIt came in a box with a user manual, extra paddle and white jumper wire. The manual has a lot of instructions and you should read it if you are new to electrical installations. If you havent done wiring before, I recommend you call a professional electrician.WiringThis is a 'self-learning' device which figures out which line is LIVE and NEUTRAL by itself. So dont get confused if the device says Line/Neutral on both poles. I have read other users had difficulty to get it work, so I followed the pole placements from the Gen-1: bottom pole as LIVE and top pole as NEUTRAL.Wiring is soooo easy! Im not an electrician but I have changed a lot of switches in my old house in the last 4 years. This was THE easiest way to plug+tighten a pole and a romex. Loosen the screw, push the exposed copper (1/2 inch long) inside, tighten the screw.If you have multiple switches next to each other (in my case 5 of them, 3 are ZWave) its very easy to keep the LIVE line common as you can do jumper from one to another.StartupThere isnt much you need to do get these switches working. If you have wired them properly, as soon as the power switched on, you should see the blue LED come on! I was able to switch on and off right away. Didnt require any reboot/reset or anything.ZWave IntegrationThis is one area where the Honeywell switch gave me grief and 1 sleepless night. I installed both the GE and this one together and side by side. First evening it just wont get detected by my Nortek ZWave stick. I almost ripped it off and sent it back. Next day morning I watched few videos and read Reddit comments and found out, you need to RESET this switch! So with the switch LED glowing, click the up paddle and down paddle very quickly 3 times. If you did it right, the LED will flash for few times. NOW its reset and ready. Now get "ADD Node" on Home assistant and click the up paddle. You should be able to see this switch after you heal the network. Phew!Signal StrengthIts actually pretty good. Considering the fact I have 2 more ZWave switches right next to this one. No interference and works well.I will monitor this switch as time goes and update this review if anything changes. If it doesnt, 5 star is my rating!
Boogaloo
2025-07-24 14:00:23
I have 4 of these particular switches at my house, as well as more than 10 of the Honeywell and GE Z-Wave Plus paddle dimmers, along with 3 of the Z-Wave motion dimmers (all 3 are GE). They were extremely easy to pair with my smart hub and have been working flawlessly so far, roughly 10 or so days in.The paddle dimmers do NOT have double tap to full brightness drivers natively. Fortunately my smart hub community is full of very talented people who have created a driver that does allow double tap to full brightness, so I have added that driver to my smart hub and it works perfectly.The GE and Honeywell versions of these switches are identical. The Honeywell versions are about $5.00 a piece cheaper, so I opted for those once I confirmed that they were functionally identical. Both are made by Jasco.All in all, I would highly recommend these switches along with the other switches I mentioned.The Honeywell paddle (non dimmer) model number is 39348The GE variant paddle (non dimmer) model number is 14291These ^^^ are the same switches under different brand names. I own both, and both work perfectly.The Honeywell paddle DIMMER model number is 39351The GE Variant paddle DIMMER model number is 14294All of these switches can be used in 3 way configuration by buying the Z-Wave "add on" switches listed below.The Honeywell add on switch model number is 39350 and works with BOTH the GE and Honeywell dimmers listed above. I Have the GE Z-Wave paddle dimmer listed above paired with a Honeywell Z-Wave add on switch right now and that combo works flawlessly. I needed an add on switch for a 3 way light, and Amazon did not have the GE add on in stock, so I ordered the Honeywell just to try and see if it would work and it did. I have no reason to doubt that the same would be true if the parts were reversed (Honeywell dimmer with GE add on).Anyway, these things just work. They are Decora style obviously, so you need to be in love with the Decora style or ambivalent to it. For us, it was easy because we were replacing all of the 16 year old Leviton Decora style "smart" switches we had, with the new Z-Wave standard, so it was a no brainer.The last thing I will say is that ALL of the switches I refer to here in this review, require a neutral. They are also a little bigger/deeper than some other switches, so if your switch boxes are crowded with giant wire nuts, you might experience some issues fitting these things in the box, HOWEVER, since these switches have screw terminals for all wire connections, you should be able to eliminate 2 or 3 wire nuts per switch, per box. THAT in and of itself, makes fitting these switches doable.Basically, I would buy these switches again in a heartbeat. They feel very well made and ALL have worked flawlessly in our primarily Z-Wave smart home environment.
Daniel Ma Gill
2025-06-26 14:40:19
Best part about these is you can reboot them with out flipping breaker. Some times they need a bounce because they quit responding. These make it quick and easy. I have 3 brands in the house, and these are the best, most reliable
Anthony
2025-06-18 15:10:12
These switches are great for their price and they work well. I have found that they can be tricky to pair. The instructions say to quickly tap the switch, but I've found that "quickly" means not too fast and not too slow. So, if you're struggling with it pairing modify the delay between taps. I've also found that sometimes these go offline and I haven't tracked down why. In Home Assistant, I have an automation set up that periodically scans the Z-wave network for dead devices and which ping those. That brings them back online.
Ellie
2025-06-08 16:55:45
I ordered a few dimmers and switches from this brand, they are made by Jasco, same mother brand as GE and Enbrighten. They are super simple, up-down like the usual switches, so guests don't get confused with odd looking smart switches. Good value for money, the whole house has them and been working flawlessly for months now. I had no trouble with them going offline, they are reliable contrary to other zigbee devices I own.I believe they are from the z-wave 500 series (latest on market is 800 series) but for what they are supposed to do - turn on/off or dim a switch - it's alright with me !
JULIO JACOME
2025-04-16 14:16:19
EXCELENTE CUMPLE MUY BIEN MIS EXPECTATIVAS
VEE
2025-04-12 19:01:02
Works so well, easy to install and very good quality. I have three so far and work very well with Smartthings.
Customer
2025-03-08 17:17:43
When matched with their primary z-wave switch, these work brilliantly. And they only require two wires, whereas the old three-way switch they replace required three. Some minor rewiring required in all of my cases, but easy to do, and no concerns after install. These feel good, and the main switch reacts instantly to input from this one.
Mike
2024-12-24 16:26:31
This is a great z-wave switch for the price. Very well built and easy to pair to hub. No issues at all. Highly recommended
Recommended Products
