Your cart is empty.
Your cart is empty.Product Description
Multifunction Use
Widely application adapt to different materials of wall, such as red brick, sand brick, brick, water brick, cement cover wall. Ideal for electricians, plumbers and other contractors
Groove Cutting Depth Can Be Set
An Angle of 90 degrees can also be cut.Safe and ergonomically optimum handling. Ensure the safety of the users by the electric leakage protector.
Easy & Simple Operation
Work should take dustproof glasses and Mask. Built-in vacuum port and water pump work at the same time to reduce the dust during work
One Time Molding
Fast automatic grooving wall tank,suitable for quick and clean cutting of wall chases. Without any auxiliary tools and the second process. Cutting groove depth can be randomly controlled.
Built-in Infrared Beam
Wall slotting machine is equipped with infrared rays and rollers. When working, it uses the roller to stabilize the propulsion while aiming with infrared rays to make the lines straighter.
Widely application
Adapt to different materials of wall, such as red brick, sand brick, brick, water brick, cement cover wall. Ideal for electricians, plumbers and other contractors
Armando Nieves
2025-07-28 11:57:05
It a well accessorize kit, the machine it self operate fairly well. I but it to cut reenforcement concrete. And so far is working fine and smoothly. The addion of the water pump really makes a difference.
Captain13
2025-07-25 11:57:33
Folks this saw is the real deal. Very well put together and solid. I was surprised when I opened the case and felt how heavy it was. Did a great job cutting a grove in my concrete floor within a few minutes. There is a learning curve on getting the water pump dialed in. Too much you get water everywhere to little dust everywhere. Once you have it dialed in with the valve at the saw you are good. I did use a wet vac to catch some of the concrete chips. Also the laser worked well to keep in somewhat on track but did get covered at times resulting in having to clean it. I would recommend this tool hands down.
Cwracing2000
2025-07-21 18:27:57
It worked great for the project I was doing. It made the Job go fast and easy. The laser beam on the handle made it easy to stay in a straight line.
George
2025-05-25 14:26:35
A+
No BS Customer
2025-05-19 11:50:11
As you can see from the pictures this machine will allow you to cut channels in Concrete to approximately 1.5“ x 1.5“. Needless to say if you use the blades dry, you will have to have a dust collection system and realize that cutting dry destroys the blades. If you use a wet system with the included water pump in a bucket, prepare for major cleanup afterwards, as you will create a ton of slurry. Also this cuts through concrete and leaves behind concrete tabs that need to be broken off by a chipping hammer and clean up the bottom of the channel . The most important thing to remember is that you cannot use this machine on a standard 15 amp outlet the minimum required is a 20 amp breaker and even with that it will trip multiple times as the idle speed uses 18 A and when you cut the concrete, you can easily go over 20 A depending on how many blades are in the machine. Another negative is that the 5.25 inch concrete blades with a 20 mm arbor are impossible to find. The manufacturer is not responsive when I contacted them about replacement blades. If you use 5 inch blades, then you lose 1/8 of an inch in depth. this is important because if you are trying to put a 1.5 inch pipe in the channel and you use a 5 inch blade, the pipe will stick out of the concrete. Overall happy with the machine and its price. Even if it ends up being just a one time use, it paid for itself.
Winston Walker
2025-05-17 12:47:13
You just have to attach a vacuum cleaner to extract the dust.
Excelente
2025-05-12 11:13:17
Excelente
HOWARD
2025-04-17 18:44:22
Saw worked great, ate through the concrete like a champ! The instructions were hard to read, they could have used a better printer! Only real negative the top handle bolt is bent because it wasn’t placed in the case correctly and broke the inside of the case. Could use a new bolt for the top handle.
Miguel
2025-04-02 17:14:34
Tiene buena capacidad de potencia a un buen precio
Ruben
2025-03-20 16:18:18
The media could not be loaded.
Beny
2025-03-10 11:08:20
Muy buena máquina, lo que haces en una dÃa con el método tradicional (esmeriladora, Sincelador, clavos, alambre) con la maquinita lo haces en 2 o 3 HRS, lo malo es que se sobre calienta, hay que darle su tiempo.
Luis F.
2025-02-18 18:02:18
Excelente calidad, diseño sólido.Te ahorra tanto tiempo y trabajo, definitivamente recomendado al 100%
Alberto
2025-02-17 21:21:13
Muy buena máquina 👌
Recommended Products