Shopping Cart

Your cart is empty.

Your cart is empty.

YONICO Raised Panel Cabinet Door Router Bits Vertical Bevel 1/2-Inch Shank 12144

4.5 (26) Write Review
Free shipping on orders over $29.99

$22.95

$ 9 .99 $9.99

In Stock

About this item

  • Create center panels for rail and stile cabinet doors
  • Premium C3 micro-grain tungsten carbide blades for a sharper & longer lasting edge
  • For use on table mount router only
  • Silver induction brazing for maximum strength and durability


Create bevel raised panels for cabinet doors vertically with the Yonico 12144 Vertical panel raiser router bit. Two flute carbide cutters & 1/2" Shank. Manufactured from C3 micrograin carbide, Yonico raised panel router bits create smooth, detailed cuts resulting in professional door panels.


Customerp
2025-09-03 18:01:25
Great product
Bruce Rasmussen
2025-08-31 18:52:33
This bit has worked well for me in fabricating replacement dutch lap siding for an old building. A vertical profile bit like this can be a bit dicey to run through the router table, so make sure you keep a steady travel of the plank, and that it is held in place with featherboards both behind the bit and after.
John
2025-08-28 14:33:34
Purchased this for the ogee bead profile. Needed it to run 63 MDF panels. The cost of this entire set was as much as a single bit at other locations. I did purchase with the intention of 1 time use, but after receiving and using the bit I needed I can say they will last much longer. I know chinese carbide is much softer then domestic breeds so I am sure frequent sharpening will be needed, but for someone using these here in there outside of a production setting, you cant go wrong. I can also tell you that these are not good for MDF panels, the direction of the cut chips out the face of the panel. Not necessarily a problem for this particular product itself (I dont think) but probably for all vertical bits. Just wish I had thought of that issue before ordering. Luckily I was able to putty and patch those that chipped beyond sander repair. Also, these are probably best suited for 7/8-1" rail and stiles thickness with 3/4" panels. I had to fudge the panel 1/16" proud in 13/16" frame to fit right without protruding out too much to be noticable. . So if you want flush panels in 3/4" frames shop elsewhere.
Mark
2025-08-25 17:58:52
This is not forgiving of any carelessness or lack of experience! I tried this out as soon as I got it with a few pieces of scrap pine wood. The slightest variations in my router table’s fence caused obvious flaws in the final project. Hopefully I get it down before I become responsible for massive deforestation.
Richard B.
2025-08-11 13:12:57
Good bit for the money, thought it might take 4 or 5 passes but got it done in 3. Just as sharp as when I started, had to make 5 raised panel doors and saved money with this bit.
doug
2025-07-19 14:17:40
Only used one bit to far. Had to resharpen 3 times over 200 ft of shaping. Decent quality.
Boris
2025-07-16 16:49:30
Very poor quality. You can actually see the serrations on the edge from the grinding process. Leaves a very poor surface finish. Not that I expected CMT or Whiteside quality at this price, but I really feel these are not worth using at any price. You'll be sanding your life away after using these. I'd return them but I already threw out the box they came in.
tammie scott
2025-07-10 15:19:12
Great product! It is exactly what I was looking for. It has a smooth cut and needs very little sanding. Ordering was easy and I received it in a very timely manner. The price was great compared to other places that I have checked. I will be ordering other bits from here.
Rodrigo Hernández
2025-07-07 18:12:00
La utilicé para unos tableros curvos, era justo lo que nesecitaba.
Gus
2025-06-29 12:27:58
Muy satisfecho con las herramientas, buena calidad
IVAN B.
2025-06-25 16:35:34
good i like it.
GingerDD
2025-06-14 11:05:18
Great product. Very pleased with packaging and router bits.
hippias
2025-06-07 10:00:58
fonctionne très bien avec de l'érable
Customerp
2025-06-04 21:47:50
Great product
Bruce Rasmussen
2025-05-25 14:20:15
This bit has worked well for me in fabricating replacement dutch lap siding for an old building. A vertical profile bit like this can be a bit dicey to run through the router table, so make sure you keep a steady travel of the plank, and that it is held in place with featherboards both behind the bit and after.
John
2025-05-21 18:16:11
Purchased this for the ogee bead profile. Needed it to run 63 MDF panels. The cost of this entire set was as much as a single bit at other locations. I did purchase with the intention of 1 time use, but after receiving and using the bit I needed I can say they will last much longer. I know chinese carbide is much softer then domestic breeds so I am sure frequent sharpening will be needed, but for someone using these here in there outside of a production setting, you cant go wrong. I can also tell you that these are not good for MDF panels, the direction of the cut chips out the face of the panel. Not necessarily a problem for this particular product itself (I dont think) but probably for all vertical bits. Just wish I had thought of that issue before ordering. Luckily I was able to putty and patch those that chipped beyond sander repair. Also, these are probably best suited for 7/8-1" rail and stiles thickness with 3/4" panels. I had to fudge the panel 1/16" proud in 13/16" frame to fit right without protruding out too much to be noticable. . So if you want flush panels in 3/4" frames shop elsewhere.
Mark
2025-05-12 16:35:56
This is not forgiving of any carelessness or lack of experience! I tried this out as soon as I got it with a few pieces of scrap pine wood. The slightest variations in my router table’s fence caused obvious flaws in the final project. Hopefully I get it down before I become responsible for massive deforestation.
Richard B.
2025-05-10 14:40:28
Good bit for the money, thought it might take 4 or 5 passes but got it done in 3. Just as sharp as when I started, had to make 5 raised panel doors and saved money with this bit.
doug
2025-04-22 10:02:03
Only used one bit to far. Had to resharpen 3 times over 200 ft of shaping. Decent quality.
Boris
2025-04-17 11:03:25
Very poor quality. You can actually see the serrations on the edge from the grinding process. Leaves a very poor surface finish. Not that I expected CMT or Whiteside quality at this price, but I really feel these are not worth using at any price. You'll be sanding your life away after using these. I'd return them but I already threw out the box they came in.
tammie scott
2025-04-16 18:55:48
Great product! It is exactly what I was looking for. It has a smooth cut and needs very little sanding. Ordering was easy and I received it in a very timely manner. The price was great compared to other places that I have checked. I will be ordering other bits from here.
Rodrigo Hernández
2025-03-11 16:16:28
La utilicé para unos tableros curvos, era justo lo que nesecitaba.
Gus
2025-03-10 16:16:07
Muy satisfecho con las herramientas, buena calidad
IVAN B.
2025-03-02 13:23:51
good i like it.
GingerDD
2025-03-01 12:22:41
Great product. Very pleased with packaging and router bits.
hippias
2025-02-09 12:45:37
fonctionne très bien avec de l'érable