Your cart is empty.
Your cart is empty.Product Description
2pcs 400W Adjustable Multi Speaker YLY-2088 Treble/Bass 2 Unit Audio Frequency Divider 2 Way Crossover Filters
400W Adjustable Multi Speaker
- Suitable for speaker power: 400w or lower.
- Suitable for speaker impedance: 4 to 16 Ohm.
- Inductance adopts anaerobic copper winding , and pure copper wire.
- Large capacity, reasonable design, beautiful appearance, quality of the sound can control according to their own interests.
400W Speaker Frequency Divider With 4 Jumpers Onboard
- Jumper A, B for bass.
- Jumper C, D for treble.
How to Use the Splitter Board:
First connect as per our diagram above (Treble, Low, Input), connect to speaker, seal air gap, we can begin to hear music while optimize. Normally we use jumper A and let B idle. For jumper C and D: we need to hear the actual effect of treble. A general formula is: A+D=better Bass; A+C=clear Treble and Bass; A+CD=clear Treble and Bass (the overall effect inclined towards Treble); AB+CD=more mediant frequency. When Bass effect is unnecessarily high, we can remove cap A. Please optimize until you think the sound is best, and then fix the board with your speaker unit.
Details About Jumpers:
Jumper A, B are used to control audio effect of bass range. A for lower limit while B for upper limit of the bass audio range. For some speakers, when Bass is turned up too much, the speaker will show distortion. When that happens: we remove the jumper cap of jumper A to limit super low Bass to bring distortion lower. When we remove the cap of jumper B, Bass is increased while cap of Jumper B is on, Bass is decreased. Jumper C and D are used to control Treble range. When cap of both jumper C and D are on, the sound of treble is loudest. When only cap C is on, the treble sound is lower. When only cap D is on, further lower. When both caps of C and D are removed, there is no treble sound. (Generally speaking, with the four jumpers, you'd sooner or later find your best sound effect. Anyway, all effects still depend on your actual test.)
Package Contents:
- 2pcs YLY-2088 400W Adjustable Multi Speaker 2 Way Crossover Filters Audio Frequency Divider
Jon
2025-07-31 09:25:53
Used as a lazy mans sub setup. Wired a sub in parallel to 6x9 speakers(each 4 ohms). 95 RMS at 2 ohms per channel dived by 2. Handles 47 RMS with no issue and improves the sound quality.
javier c.
2025-06-24 18:41:23
Was able to separate my bass with the voice on my speakers
Jeffrey L Chaplin
2025-06-18 11:09:55
Working great on my 12 solo baric with horn driver
Levi K
2025-05-11 11:07:27
I used these to convert an expensive active soundbar to passive after the electronics went. I have two tweeters and two drivers on each crossover and they come out of it at 4 ohms. They are labeled in english now, even though the pictures don’t show it. Still no instructions, but the description has good enough instructions. They did a great job and the soundbar sounds awesome, maybe even better now that I’m here is a receiver processing the audio. I’m impressed.The only negative is they are shipped pretty carelessly. In an anti-static bag in a padded mailer with no other protection. At least throw some bubble wrap around them or something, one of mine came with bent pins on the D jumper.
Mrs. Joan Lewis
2025-04-24 11:36:23
There are two sets of jumpers for setting cross over frequency and rate of crossover. No instruction sheets were provided. On the internet, I could quickly not find any information as there is no model number provided for this crossover. On the PCB nearly everything is in Chinese (or an Asian language), As a Texan, this I know from nothing.
Fernando
2025-03-02 11:26:08
El.sonido es bueno. La.opcion de configurar las frecuencias es ventajosa
andy
2025-02-24 13:56:59
These are 400 watts combined (even that is questionable), not actually 400W crossovers.
Terrible T
2025-01-16 15:03:28
Works great with my SV151 speakers.
Recommended Products