Your cart is empty.
Your cart is empty.Product Description
- What you Get --
- 4 x Hall-Effect joystick,
- 4 x Thumbstick Cap,
- 4 x Protective Ring,
- 2 x Thumbstick Grip,
- 27 x Screws,
- 1 x Metal Cross Screwdriver,
- 1 x Metal Tweezer,
- 1 x Metal Pry tool,
- 1 x Pry bar.
Protective Ring -- 0.1 Ultra-thin protective ring compatible with PS5, PS4, Switch, Xbox controller.
- 27 Screws for PS5 Controller
- PH00 Phillips Screwdriver (2.0mm)
- Metal Tweezer
Carlos G.
2025-09-06 14:41:43
Awesoma worked perfect 10/10 all of the work
Angela S
2025-09-05 17:45:46
Work as expected for a PS5 controller that was previously experiencing drift. 3 of the 4 would have been fine with no calibration, but one was drifting slightly in game play. Went online and calibrated them on DualShock/tools.github.io. A few other reviews had mentioned issues with their R3. In my case, no issues with my L3 or R3, they still work fine.Removing the existing hardware is a pain, in part due to the number of pins involved and the fact lead free solder requires a higher temperature. After spending too much time trying to desolder ~14 pins and remove as a whole assembly, I ended up breaking it down into smaller parts. For example, disconnected a pot and removed just those 3 pins. Much easier doing it in small steps. Once I got the hang of that trick, the second (left) one took half as much time as the first (right).A nice small flush snippers, desolder braid, and flux are the accessories you need - in addition to a soldering iron and solder. If you don’t know what those are, then this project probably isn’t the one for you.
Johnny
2025-08-28 12:37:27
These worked well but I lost functionality of r3 on both of the controllers I replaced these with. I had to make a custom modification to resort the re button which more than doubled the workload.
Joshua
2025-06-24 13:01:27
Other than calibrating it worked better quality than the original ps5 joystick
Justin D
2025-06-13 15:00:42
So, I just installed these today and I gotta say - they do work. But immediately after the sticks were all wonky. My let one was pointed a few degrees up, and my right on a few degrees right. I checked these using some common online controller GUIs. There is a solution however, as there is also an online tool that will recenter your controllers for you. With that recalibration they have so far been perfect - but if they fall out you can rest assured that I'll be coming back to lower my score further. Absolute nonsense that I should have had to jump through such hoops after installing these things (which it is already a bit of a pain to desolder the old joysticks)
Michael Evans
2025-05-13 14:06:22
Used these to replace the joysticks on my PS5 controller. I have only used 2 of them so far but I am keeping the other 2 for when my other controller starts to drift. They are not easy to replace but that is Sony's fault. These fit the control board perfectly and work great so far. I have not checked the calibration or anything but I don't have any issues playing any of the games I play. There is an equal amount of dead zone in all directions as far as I can tell and no more drift or ghost inputs. The kit is nice and helped. I didn't use the joystick caps, I like the ones that the controller had originally and these feel a little harder and more like plastic, but it's nice to have extras in case I ever need them.
Ed
2025-04-08 11:01:46
soldered two onto controller board and both work fine for my game play. mostly single player rpg type games. if installing on bdm-020 be careful of tiny resistor next to right stick up-down sensor.
TW
2025-04-06 11:07:39
Spent couple hours trying to get them calibrated and this was as close a they would get. 2 controllers and 4 of these and this is what I got. The other was even worse. Now I have to start over with the repairs! Not really an ready task. I expected much much better! Refund or replacement of GOOD ONES would be the least they could do!
Customer
2024-12-03 10:10:14
All four joysticks I installed worked after I calibrated them online at dualshock-tools.github.io. However, they did not perform well initially in the circularity test and required lots of tweaking using the online tool's custom range calibration. Also, while the L3 & R3 button clicks worked, I find them to be too sensitive; I often accidentally click down on them unintentionally - I do not have this problem with standard PS5 or TMR joysticks.I had no problems installing these joysticks, you get lots of extras with this package, and you won't need to ever worry about stick drift. However, they do not calibrate well and L3 & R3 button clicks are too sensitive for me. I recently installed Aknes TMR joysticks and find them to perform much better.
Recommended Products