Your cart is empty.
Your cart is empty.Product Description
Mike
2025-08-17 12:52:52
Price was awesome for 4 fast Metal Gear 20KG Servos! worked perfect on two of my 1/10 crawlers both with rear steer definitely an upgrade over the 6KG stock,
Lunacy
2025-08-03 16:10:30
Only used 2 of the 4 so far but they are working great in my Tamiya TT02 and M05, so far. I'll update if they stop working like some others had experienced.
B. Pearce
2025-07-27 20:47:11
I got these servos to use for a small electronics project (completing a 100 jump challenge in Mario RPG, haha). It was a fun motivation to gain a little experience working with electronics hardware.My first attempt used a little 5 volt 2 amp power supply I had laying around, and wired directly to a Raspberry pi 3b. But it turned out this was not nearly good enough, as the servo would move erratically or not at all. I upgraded to a much stronger variable voltage desktop power supply and put a proper servo controller between the Pi and the servo, and then it worked great. There are wiring diagrams on adafruit and tips on reddit. The best way to learn is to try!
Andrew Staats
2025-07-16 11:15:33
These aren't the best servos you can buy, but they might be the best you can get in this price range.I bought 20 of these to build a hexbot; overall they work OK. They're a little noisy and loose and sloppy in their control. I had 2 fail (lock up/burn up) and probably 2 more with positioning issues that cause them to oscillate when they should be still.All that being said they're "good enough" - I'll forgive a lot of these sins for the price point. With the better alternate being 4x the cost, they're cheap enough I can buy extras to swap out the ones that have issues.
Nathan Jones
2025-07-07 10:41:56
Crazy torque for a cheap servo
Anthony
2025-06-29 12:07:08
They work like I expected.
Alex
2025-06-09 14:53:12
Thus far, the single servo I've put to use has only been used in one test flight, so I don't know if there are any longevity issues with these servos. What I can tell you is that the ones I received are branded "Deegoo FPV" and all the gears are metal. I've seen other reviews mention plastic gears, which I was okay with when purchasing, as I needed cheap servos for my project. The photos of the servos with plastic gears have a different name on the stickers than mine do, so if you order these and they don't say "Deegoo FPV", they most likely have different gears, and I'd return them for replacements.The only con for me, is the grease seeps out of the casing, and can leave grease marks in a toolbox or plane. But at least they're lubricated!
James Davis
2025-04-04 19:56:00
All four worked as expected with no issues. You do need to drive them with a separate power supply rather than directly from the Arduino Uno. While they moved when driven by the Arduino Uno they were very slow. A small separate power supply worked well driving two at once. I suspect that small power supply would drive more than two but I haven't tried it yet.
Judhi
2025-02-25 19:25:09
Motor rotates as expected from 0 to 180 degrees. Power efficient, it even works with 5V supply from Arduino, but for long term would be better to use separate supply.
sonny
2025-02-13 17:59:25
After only a few minutes of use, I noticed that the servo would completely stop spinning, even when I could hear the motor running. After opening up the housing I noticed that the one of the gears was completly stripped, but also that only 1 of the 3 gears was actually metal. Tldr, dont buy these servos if you need any semblance of quality
Customer
2025-01-30 12:48:48
Great replacement for plastic gear servo’s
Dilip
2025-01-07 16:08:13
Wrong description, plastic gears and not working, all four which I received
Marco
2025-01-02 13:01:06
Bo bon po chere
Recommended Products