Your cart is empty.
Your cart is empty.Product Description
DSC
2025-08-29 12:46:06
Been trying to upgrade all the lights on my old 03 Silverado work truck to LED. Pulled the trigger on these. Had the flash fast on the turn signal but added an inline plug & play resistor and worked perfectly for turn signals also. Tried to add amber to front marker light/turn signal but needed to order resistor for front also. Really helps to pull the wires out just a tiny bit from the plug to help make contact and hold in better. Will follow up if things go bad. SUPER easy to install.
Michael C.
2025-08-10 17:13:13
poorly built, bulb sockets do not fit right in a 7443 housing. Connections suck.
ronald garvin
2025-07-04 10:54:35
Very convenient way to correct the flicker issues without cutting the wire harness
Rick W
2025-06-04 13:10:26
Works good so far. Absolutely no flicker.
H. Haulman
2025-05-12 15:19:50
Swapped out for LED, so naturally the load changed. These corrected the issue without having to cut and splice in separate resistors.
Philip
2025-03-14 10:11:37
installed and only 1 is working no hyper flashing even the resistor is not that hot, but on the right side hyper flashing and resistor is hot to touch.
Swampotter
2025-02-25 14:27:19
Hard to give it a proper rating. I got them for my Infiniti turn signal lights. After installing, only 1 light would work properly. The other one wouldn’t turn on at all. I’ve tried every option for polarity and that didn’t work. Swapped the resistors with no change. No matter what combination of resistors I used, right/left, polarity, bulbs… nothing worked. Clearly there’s an issue with in line resistors for my car. I bought 2 sets of these, all worked on their own but when connecting more than one they didn’t work. It could probably be modified but I didn’t buy these to modify them.
Miles Passell, PHD
2025-02-19 15:15:20
This is a great bit of kit if you're retrofitting LEDs in place of filament bulbs. I'm no stranger to soldering, but it can be a bit of a hassle to make your own wiring harnesses. I'd know because I had to make my own harnesses for a tail light rebuild/retrofit. For the front end my project was going to be much simpler with only resistors for the turn signal bulbs, but I didn't fancy trying to solder these resistors inside my engine bay, nor taking the time to disassemble all those wiring harnesses at the front end to do a proper job on a workbench.Enter these fabulous (and very affordable) premade wiring harnesses. Easy as plugging it in and I was good to go! Quality is excellent, but I can't rate longevity at 5 stars because I've only had these a few weeks. Fitment of the bulb socket into your light housing will vary! I had to snip and shave some extra plastic off the locking tabs to make fitment, took all of five minutes with some nippers and a file.Superb, affordable, time-saving, plug it in and you're done, proper job wiring harness to take your jalopy into the 21st century!
ناصر عبدالله
2025-02-14 16:01:09
بعد التركيب والاستخدام ارتÙاع ÙÙŠ درجة Øراره عاليه ÙÙŠ المقاوم بشكل مخي٠..مم قديسبب Øريق لا Ø³Ù…Ø Ø§Ù„Ù„Ù‡ للاجزاء البلاستيكية ÙÙŠ السيارة
Guillermo Mendez
2025-02-07 15:20:11
Los compre para las direccionales de mi Jeep Liberty 2012 ya que la descripcion decia que eran para focos 3157…y si son pero no para los de mo vehiculo, el conector es diferente…tuve que cortar las resistencias y soldarlas al arnes del vehiculo para que las luces led que instalen ya no marcaran error y parpadearan muy rapido, quedaron funcionando correctamente
Recommended Products