Your cart is empty.
Your cart is empty.Our ceiling medallion collections are modeled after original historical patterns and designs. Our artisans then hand carve an original piece. Being hand carved each piece is richly detailed with deep relief, sharp lines, and a truly unique touch. That master piece is then used to create a mould master. Once the mould master is created we use our high density urethane foam to form each medallion. The finished look is a beautifully detailed, light weight, solid construction, focal piece. The resemblance to original plaster medallions is achieved only by using our high density urethane and not vacuum formed, "plastic" type medallions. - Medallions can be cut using standard woodworking tools to add a hole for electrical or a ceiling fan canopy. - Medallions are light weight for easy installation. - They are fully primed and ready for your paint. If you have any questions feel free to ask. These are in stock and available for immediate shipment.
Lisa
2025-08-20 20:25:54
Priced right, pretty, covered someold electric wiring with great style!
Cordell
2025-07-20 17:53:52
Nice accent to old ceiling light outlet.
Robert
2025-07-02 14:12:01
These medallions are great. Used them for our pendant lights in the kitchen. I needed to make a fairly large hole to accommodate my new lights. I used a pumpkin carving knife, worked great! As another reviewer said, the primed white was perfect. I didn't bother to paint them.
whatever
2025-06-24 12:39:37
I needed to cover up about 8 inches of damage from old fixtures. My new lights have only a 5 inch base.I looked at the "box" hardware stores, they don't have many options, and those options are ugly.These Ekena CM07AL plates were just what I needed. I drilled the center holes just using a pocketknife. The material is solid, but very easy to cut.Installed in minutes, came out great. I didn't even bother to paint them, the white priming looks fine as-is.
Robert John Bush
2025-06-17 18:21:53
Got here fast. Went over old fan opening in ceiling with a couple of spots of caulk. Looks good but doesn't dominate the decor. Better than doing patch work on a textured ceiling. Had to level out area a bit with putty knife where attached.
Pinky
2025-06-07 12:40:51
Used to cover up previous light fixture cutout, covered perfectly and added nice touch. Easily paintable, I spray painted with a chrome/silver spray paint. Lightweight and easy to cut to you size needed. Great price.
Johnny
2025-06-04 21:59:15
I drilled a pilot hole dead center for a recessed screw. Screwed it to the celing with a small piece of plywood on the back side of the sheetrock and caulked around it. After painting it looked perfect and it will be easy to remove when my wife changes her mind as usual.
The Rev
2025-05-28 11:47:38
We added molding to the builder’s mirror directly beneath the bathroom light fixture. But now we needed something to extend the light so it stuck out a bit further from the wall so the globes would clear the molding. Ta-da! This was an elegant and useful solution. I actually like the light better now!
Alejandro Villanueva Nolasco
2025-05-26 15:36:03
muy buena calidad
Noëlla Côté
2025-04-04 13:50:38
très beau mais trop petit. Voilà pourquoi je l,ai retourné
Darlene Falls
2025-03-19 13:10:03
I had a hole in a popcorn ceiling of a rental unit I have, a result of some plumbing repairs. The hole was in the centre of the ceiling. This was an attractive and economical solution to the problem of trying to repair a popcorn ceiling.
Iceman
2025-03-07 15:51:19
The ceiling around the old light was rough.This was easy to cut the hole and it looks amazing
Carl Tremblay
2025-02-05 17:38:26
Acheter pour groupe pour couvrir une boîte électrique au plafond c'est fait très bien c'est fait de polystyrène mais je trouve que ça coûte un peu cher
Recommended Products
$40.18
$ 21 .99 $21.99