Your cart is empty.
Your cart is empty. Description:
3 terminals, SPDT (on/on) 2 positions, easy installation.
Can be used on low voltage or high voltage (AC 250V 3a) circuits, ideal for switching lights or motors.
This switch is not momentary. Widely used in all kinds of electronic products, instruments and meters, household appliance field.
Such as: automotive electronic products, communications equipment, military products, testing instrument, gas water heaters, all kinds of small home appliance, lighting, etc.
Package Includes:
10* AC125V 6A ON/ON SPDT 3 Terminals 2 Position Toggle Switch MTS102
Jim S.
2025-08-25 10:03:28
No complaints. For the price, these are decent switches. Don't go crazy on the soldering iron with the heat and they will work just fine for you.
Torte
2025-08-13 15:13:49
These switches came in a pack of 10 at 6.99 us in May '24. I've used two of these in an amplifier as a 12v power switch and a mixer on on. Both have worked great without any false positives or hangup. All of my connections were soldered at 400c without any melting or disfiguring of the switch. Just be sure to tin the leads and the wire before trying to make the connection. They are very small and work perfectly for PC jumper or rc transmitter switch replacements.
Edward Hickcox
2025-08-06 20:32:20
These switches seem to be high quality. They've got a very low closed circuit resistance and solid mechanical snap when switched. My only issue was, when soldering done 22ga stranded wire to the terminals, I had to turn the temp on my soldering iron (TP80-S mini iron) to 380C to get the terminal lug hot enough to melt the solder into the joint. A couple of times I held the iron to the terminal too long and the plastic got soft, fast. On one switch I was able to press the terminal back into the switch and get it working again, but the other just pulled straight out of the plastic housing. So now it's an SPST on-off instead of SPDT on-on. 370C was a little gentler on the switches, but keep an eye on your temp, and your iron's time on the component.
Arthur B.
2025-07-09 14:18:20
Excellent choice for everyday projects needing a SPDT miniature switch. Plastic body may not stand up to long term use. Works fine for dry circuit switching as well as AC.
gui
2025-06-26 09:10:02
These are good switches that work fine but they melt if you have to use any amount of heat from the solder gun. I tired to heat up the post a bit and it the connector melted out of the plastic housing. I found that out the hard way. So don't heat up the connector, tin the wire before putting it through the hole and drop solder on the post and take away the soldering gun they're usable. Just my take on em!
Just saying
2025-06-13 10:00:40
They are small and work in both directions. I dropped my remote control and this switch fits in the same spot..
Camper Van Beethoven
2025-05-04 17:48:53
Never knew something could be so shoddy. Tried using my first one and discovered the plastic has ZERO resistance to soldering iron heat.The wires soldered on OK but I noticed a little movement.Tried to unsolder a wire and soon discovered the plastic has the melting point of beeswax.I've soldered these types of switches for 40 years and have never seen anything so fragile.For the replacement switch I didn't even bother threading the wires through the holes, just tack soldered already tinned wires onto the sides. THAT'S how weak these are.More Chinese JUNK!
Chris L8
2025-01-29 13:55:57
I've used ten of these switches (one package) so far in my project and they work fine. I didn't have any trouble soldering or mounting them. They mount into the panel fine.The tab on the "locator washer" is a little flat, but I bent it up with plyers and it stays in place.They seem identical to much more expensive switches I've used before.
Maurice Tremblay
2025-01-04 10:41:06
Petites gadgets et réparation et ils sont très fragile à la soudure.
Recommended Products
