Your cart is empty.
Your cart is empty.Introducing the Drawer Front Installer Clamps for Woodworking by POWERTEC The POWERTEC Drawer Front Installer Clamp makes for the easy and accurate installation of perfectly aligned front drawer panels. Conveniently accommodates to different sizes drawer faces and stock thicknesses for optimal versatility. Use while the drawer is Closed for Easy Accuracy CheckingThe cabinet clamps face frame holders feature a small clamp pad profile that allows you to easily install the drawer front panel while it is inside the drawer frame itself. Want to close the door to double-check your alignment? No problem, this clever device will not get in the way. NonMarring Clamp "hands" Are here to HelpTwo non-marring, high-utility clamp heads supply you the help you need to get the job done right, every time. Each drawer front installer clamp holds the panel so you don’t have to, thus freeing you to do ensure that the drawer front adjustment is exactly the way you want it.Micro Adjusting is Easy & PreciseHandy adjustment screws allow for essential micro- adjusting, so you know it’s right before you permanently attach the front panel and seal the deal. Saves time and hassle and insures satisfyingly flawless outcomes. A " must have" in your workshop arsenal. Enjoy perfection in your drawer making projects with this ingenious device. An Essential Component for the Following Folks:WoodworkersCabinet MakersFurniture MakersDIY EnthusiastHome ImproversContractor
Heather Crawford
2025-08-24 15:27:05
We remodeled our kitchen ourselves and I bought these to install the drawer faces. They worked so good, I am so happy with it. I doubt I'll ever use them again but for how easy they made the install go, I can't find anything to complain about and would buy them again if I needed to. Excellent product!
David M
2025-08-08 12:44:22
I read some reviews about these being flimsy. I did not find this to be true. I think they strike the perfect balance of strength and thickness.They're for aligning drawer faces and holding them in place while you sink a couple screws, they don't need to be much more robust than that. Any thicker (and stiffer) and they might not fit a closed drawer.BTW - I previously owned a set of the Rockler clamps (lost one of the clamps) and these seem identical.The left / right adjusters weren't helpful for the drawers I was working on, though, because the overlays were too large. That said, had I bought the Kreg clamps I doubt they would have even fit in the clamps.TIP - If you find they don't have enough holding power for you, throw a quickclamp on before you drill and screw the box and front together.
Scott
2025-08-05 16:57:05
Not too long ago I started to make some wall cabinets, then floor cabinets. Wife wanted a counter top-drawer system in our pantry. And these came in handy. They definitely would have been very helpful on all my other past projects for sure. And they will be helpful on every project that has drawers in the future !
Gretchen
2025-08-04 14:11:41
The clamps work pretty much exactly as expected. They are easy to attach to the drawer box, and the front clamps allowed me to hold the drawer face on while I got it aligned just right.My left-hand clamp wasn't quite as square as the right-hand one, but it didn't really affect the install process. I didn't find the left-and-right adjustment screws super useful, but if I was dealing with more accurately assembled boxes & faces, I could see how they could save a lot of time on repeated alignments.I did have an occasional drawer face get misaligned, but it turned out I was pushing too hard on the face and causing it to shift the drawer slides out of alignment. Once I removed my spacer shims and screwed on the face, it bounced back. So a recommendation here is to make sure you always loosen the front clamps before making even small adjustments.
Stephanie Russell
2025-07-31 11:25:39
These made the pile of drawer faces I needed to attach about as simple as it could have been. If you're ever installing drawer faces just get them and save yourself a lot of trouble. The back clamp is very strong and holds tight, the side fine adjustment clamps hold your overhang really well from face to face and allow for small adjustments where needed, and the front clamps hold the face tight if needed (once its all fully aligned) but can be light enough to hold the face secure while still making small adjustments. The only issue I had was that the side (fine adjustment) clamps stick out far enough that they were bumping the face to their side and if it was hitting only one side then the soft-close drawer slides were pulling the drawer in at a slight angle so the horizontal alignment was slightly thrown off. Just something to be aware of and pull the drawer back out a slight bit so the soft-close system isn't pulling the drawer in.
Dust Maker
2025-07-23 14:30:02
The clamps seem to be well made. I added some self adhesive pads to the hard plastic ones to protect the drawer front finish. Much cheaper than Rockler branded ones that I was originally looked at. These are almost the same product but at a MUCH better price.Would recommend if you needed to install drawer fronts. Especially if the cabinets are already installed.
DNF
2025-06-30 13:17:32
At first I really liked this clamp set. Cheaper than Rockler and appeared pretty much the same. The metal flexes a bit when clamped, but overall they work as expected. Made installing 10 drawer fronts much easier than trying to cobble together some clamps.The reason for 3 stars instead of 4 or 5? Well, it was getting late so I left on of the fronts clamped in place overnight to complete my install in the morning. I am using professionally finished custom drawer fronts (4 coats of machine-applied finish), and the rubber (oil?) from the pad leached into one of my white drawer fronts. This is IN the paint; I tried multiple ways to remove it and nothing has worked. I’m probably going to need to order another $100 drawer front now, because blue-grey circles embedded into my drawer front is just not acceptable!So if you use them quickly and don’t leave them clamped, they work well. But DO NOT leave them clamped for extended periods of time!
William Trudo
2025-06-27 16:02:30
So glad I purchased these. Small adjustments to line fronts, plum and level were made easy!
Mr. J. S. Newton
2025-06-15 10:56:53
Bit fiddly to set up and don’t really hold the face, I gave up and did it without them
Pat Saxon
2025-05-04 16:22:14
Worked the same as some of the more expensive name brands. Holds the "false" front of the drawer tightly enough to stay in place but with enough adjustment (while holding) to position the front perfectly. If you give yourself enough clearance between the drawer side and the underside of the opening, you can then close the drawer almost completely to help with alignment (you need 5 mm or more clearance).
Kunde
2025-03-26 13:55:37
Funktioniert,Leider kann man sie nur gut einsetzen wenn es sich um Einzelschränke handelt.Wenn rechts oder links daneben eine zweite Reihe Schubläden ist, dann sind die Bügel so breit, dass man die andere Reihe Schubläden entfernen muss.Dies ist eigentlich nicht schlimm. Sollen aber die Fronten, der Schubläden daneben mit den gerade zu montierenden Fronten in einer Flucht sein, so kann man dies nicht gewährleisten, da diese ja dann ausgebaut sind.Sonst aber gutes Produkt.
Aron
2025-02-27 10:31:19
Es útil y práctico 😉
Customer
2025-02-06 20:25:07
This is the extra hand you were looking for that can hold the face of the drawer while you set up your spacing. Especially convenient if you have to install the drawer fronts before the handles.
Recommended Products
