Shopping Cart

Your cart is empty.

Your cart is empty.

QDenglamp.Motion Sensor Light Switch PIR Sensor Smart Detection Time Delay Adjustable Infrared Induction Detector for Strip LED Ceiling Lamp (5V-24V)

Free shipping on orders over $29.99

$14.55

$ 6 .99 $6.99

In Stock

1.Style:5v-24v


About this item

  • Two voltages are available: 5V-24V and 110V-265V; Load Power :≤40W ;Best sensing distance:3-5M ; Mounting Hole Diameter:25mm/0.98inch
  • Red line is Live wire (L); the outermost blue line is Neutral wire (N);Yellow line and inside blue line connect to light bulb or energy-saving lamp(Note: the 5V-24V option can only be used if it is connected to a transformer)
  • Auto switch on/off in the dark when you enter into the induction range, and the time delay has 3 way of 15 seconds, 45 seconds, 5 minutes adjustable
  • In addition to the automatic control of LED lights, it can also be used to control exhaust fans, doorbells or other devices.



Product Description

参数

Product description

1

  • There are three photosensitive modes and delay time to be selected to meet the needs of lighting under various conditions
  • Select a suitable position for installation according to the sensing range and angle of the product to avoid being insensitive or unable to sense due to exceeding the range

Wiring mode of the product

2

Attention

  • The above includes two wiring methods. It should be noted that the maximum power carried by this product is less than 40W. Exceeding this power will cause the product to fail to operate normally

Installation diagram

低压

Installation method of low voltage option (5V-24V)

For the low-voltage model, you need to ensure that your output voltage is 5v-24v. If you exceed this value, the product will be damaged

1

Installation method (110V-265V)

This option requires a household voltage with a normal output of 110v-265v. A low or high output voltage will cause the goods to fail to work normally

Effect description of product induction

1

Daytime

In the daytime or when there is enough light, the induction will not be triggered if there is someone or no one passing by(Except under the option of Allday)

1

Nighttime

It can be sensed normally at night. After the personnel leave, the light will go out automatically according to the time delay you set. When someone passes by again, the induction will be triggered again

1

Nighttime

In the case of insufficient light at night, the lamp will not turn on automatically when there is no similar human characteristics, and will only turn on when it senses the human body

1

Nighttime

If someone stays still in the sensing area for a long time, the switch will also turn off the light according to the set delay.It doesn't mean that if people are always within the sensing range, the lights will be on all the time

Places where the product is suitable for use

1

Corridor

2

Garage

3

Staircase

4

Porch


Mike
2025-08-26 15:02:11
The 120vac model works perfectly. I am using it to keep raccoons from entering my barn. This sensor is wired to a relay coil. I use the NO contact to turn on a 12DC electric magnet which locks the critter door shut. They are able to leave, but cannot re-enter the barn once they're outside. It works great. The raccoons were all out after the first night.
John
2025-08-24 18:36:12
I should have read the reviews. The 5-24v do not work. Both did the same thing. The light comes on and stays on. It doesn't matter which setting or what the voltage is. Tried with 5v, 12, and 24v and tried all the combinations of switches. It isn't a dead short so it is in the electronics. Waste of time. Waste of money.
James Cantrell
2025-08-23 16:04:45
The media could not be loaded.
Steve Lucas
2025-07-02 17:14:02
The media could not be loaded.
Robert
2025-06-08 10:23:18
Works perfect in the closet for automatic lights. Once mounted, easy installation.
M. Morimoto
2025-04-12 14:53:45
It has a setting for 5 minutes but it shuts the light off after about 10 seconds. Cheaply made so I hope it lasts a while.
thom
2025-04-01 15:12:48
Works like a charm below my antique wall sconce. Could use longer wire leads but my application was a little unusual. The light settings are spot on and detects movement at pretty sharp angle.
J. Watson
2025-03-26 15:09:01
Was trying to use this to control LEDs for my interior stairs. It is wired from the 110v to 24v ballast, once converted to a 24v signal I connected this inline between the ballast and the LED strips and regardless of which setting I have it on it will not do anything besides stay on as if there was no sensor whatsoever.I even tried putting the sensor into a thick cardboard box not allowing light through and made no difference at all... I got a 2 pack of these sensors and was planning on using one for the top and another for the bottom sections and tried both without any difference. Neither one does what is advertised unfortunately...
Carlos N.
2025-03-09 10:23:35
FACIL DE INSTALAR, FUNCIONA COMO SE DESCRIBE, LO COMPRARIA DE NUEVO
Eutimio
2025-01-18 15:10:34
Tiene un alcance muy bueno y es bastante sensible al movimiento. Sin duda es un excelente producto
Recommended Products

$35.97

$ 16 .99 $16.99

4.3
Select Option

$29.38

$ 13 .99 $13.99

4.8
Select Option