Your cart is empty.
Your cart is empty.RV Designer started in 1993, making custom drapes for RV windows. Since then we've learned to appreciate the RV Lifestyle and the RV community, and have worked hard to create products that make RVing easier.
Derek Carter
2025-09-06 13:58:22
Great outlet
Jason the Elf
2025-08-12 09:37:44
a) Straightforward and easily identifiable packaging. B) Three parts Faceplate ( you need to push it off the outlet plate) , outlet plate , and back plate. c) These are not super easy to install, but none of them are. The hard part is installing the wires into the connectors and closing the back plate. I have included several pictures. D) Here is some installation advice:!!!! Unplug/power your RV and check the outlet is dead!!!!. You do not need to strip the wires , in fact it is safer if you don't. If the previous outlet pierced the insulation on the wires, try to line up the piercings with the new connectors. The connectors will cut the insulation when you add the backplate.. You can pluck the wires out of the old outlet with small pliers or a screwdriver. Try to push the wires into the new outlet by applying pressure with a small flathead screwdriver. Do not try to force them in all the way, you just want them seated so they don't pop out while you are pushing on the backplate.. both outlet plate and back plate are clearly marked where the black, white and ground wires should go.. Push the two plates together ar mush as you can with your hands. Don't get frustrated as you may only be able to get them halfway, As you see in the photos, I placed two pieces of board flat on each side and compressed with a vice until the back plate side tabs snap into place.. Before you place the unit into the wall , I would recommend you unscrew the retaining clips ALMOST all the way out. Then make sure they are folded in and place into the wall. Hand tighten while holding the outlet in. When you tighten the screws the retaining clips will rotate so they are horizontal and hold the outlet in the wall. do not overtighten.... just snug.. Gently push faceplate onto the outlet . These are a bit more expensive than some of the others on Amazon, but I recommend these. I have a Lance travel trailer and these are the exact replacement. They are sturdy and look great!
James Barr
2025-07-12 10:04:43
Apparently an over zealous GD manufacturer worker over tightened the outlet screws in my 5th Wheel. I have replaced four broken outlets in the RV unit. This particular product is an exact match for the original outlets. Same quality, same appearance, and the same size. Easy to install? With practice yes. By number four I had the install time down to twelve minutes. The key is placing the outlet on a firm surface to push in the wires.
Richard Balabon
2025-06-14 17:34:24
Hard to get the wires to lock in the back but that is normal for these type of outlets
Campbell
2025-06-02 17:57:01
Great replacement for a RV outlet, 15 amp, hard to install unless you have the right tools but finally got er done. Price was reasonable
Eric O
2025-05-30 13:53:26
Easy to install and perfect replacement.
Rick
2025-05-26 18:13:28
Had a broken outlet in my 5th wheel and found this in black that matched what I needed. Replaced with no problems. Recommend this product to anyone that needs a common match for any RV outlet
Rick M
2025-04-25 13:49:16
Once installed, the outlet is great. It might have helped to have some kind of template for cutting the hole. Mine was a new installation as opposed to replacing an older defective one. I suppose if one had the recommended tool for attaching the wires, it would have been quite easy. For the do-it-yourselfer that likes to put time out camping instead of working on the camper, this might not have been successful. I found it ridiculous to purchase a tool to install one outlet. I was able to get the job done by sandwiching the plug between two pieces of wood and compressing the whole thing in a six inch C-clamp which I just happened to have. I tried many other methods of getting the wires crimped into the plug to no avail. In all, it took about two hours to install, part of which was figuring out how big and what shape to cut the hole where I mounted it (thus the comment that it would have been nice to have a template). The rest was getting the romex wire attached to it. Actually mounting it to the wall was easy. Overall, it was worth the effort because now my Coleman 17B has a 120V outlet under the table to use with my computer, bug zapper, or blender on the table.
DFM
2025-04-10 18:13:36
Perfect replacement for the outlet that wore out.
Gary D.
2025-03-28 11:30:12
Easy install, perfect fit in the thin walls of your RV. Good quality 👌
Daniel Ricard
2025-02-21 11:52:20
Prise conforme pour VR, elle est installé en un tour de main.je recommande ce produit pour VR
stephen scott
2025-02-02 21:30:29
Used it in my RV , was easy to install. Took some pressure to force wires into connectors but not much . Works great
D Carter
2025-02-01 17:12:11
I was doing an end of the line receptacle installation, so pretty straightforward and easy, but found it almost impossible to press the wires into vee slot. I had to strip the wire and then was able to press the wires into the slots. Instruction's show the use of a special tool to press the back plate and wires into place. I was just doing a 1 plug addition so don’t want to buy a special tool for installation . Plug is working fine though
Recommended Products
