Your cart is empty.
Your cart is empty.Product Description
Customer
2025-09-05 18:53:32
I used the 80% Siraya Tech Sculpt High-Temp Resin with 20% white Tough Resin I had on hand to make new sockets for a tube preamp I am refurbishing. . I did some tests with 100% Sculpt but when I did my offline temperature tests, it withstood the heat but the thermal shock from getting hot and cold quickly caused the thin areas to crack. By mixing with some tough resin, I was able to make a part that has held up to the ~100C temps without cracking. The pictures show the before and after the the tube/socket replacement. I will definitely be using Siraya Tech Sculpt High-Temp resin for future projects. By the way, it printed flawlessly! (I use a heater inside the chamber set at 90F.)
Alexandre Masse
2025-08-30 10:37:01
Sculpt ultra is one of the most amazing resins I've used and really shows the trickle down of material science to consumer level printers. It barely absorbs any water or solvents and is incredibly rigid. It's very ceramic like in many ways, probably because it IS filled with ceramic particles. It's a bit difficult to print, bed needs to be leveled just right and more importantly, because the resin is so opaque, the z-height needs to be very small to not have bed adhesion issues. I had a ton of issues until I realized that was my problem. Whenever I level my bed, I then set the zero a couple steps down and everything is good. The prints come out very smooth and because it's so brittle, the supports come off the cleanest of any resin I've tried. It also means you can't drop your prints as it will shatter like glass. Highly recommend for specialized use cases where you need high chemical, wear and heat resistance.
John Fitzgerald
2025-08-27 18:37:57
Fantastic Resin
theSLAchannel
2025-08-15 12:23:39
I bought this primarily to make molds to cast urethane parts in, and it does a great job at that. But I've also printed some tiny objects just to see what it- and my printer- could do.The chair and cubes have no post processing other than support removal. The large cube is 6mm. The resin prints slightly oversize, cube ended up being 6.18mm, but it is consistently the same.Printed on an Anycubic Photon. 100 sec first layers, 15 sec exposure.**UPDATE**I've continued to use this, and have been VERY impressed by the results. Excellent details. A great resin at any price, but an absolute STEAL at this price.
Timothy P.
2025-08-12 18:03:36
Printed perfectly fine! Haven't had a chance to test the heat resistance yet. The parts are accurate and clean! One thing I did notice is the color isn't clear it's more of clear yellow, a very light yellow yet still yellow. I even mixed some with some abs like Grey I had laying around to see if it would help the heat resistance with that as well, gotta day had no issues printing the mix! Will buy again!
Jonathon Hernandez
2025-07-10 14:37:34
I printed this hose adaptor for our projects. It worked out great. I feels like ceramic and breaks like ceramic. Just be careful when sanding it you don’t want to breath the dust in. Worth the buy
Great stuff. Easy to work yet.
2025-07-01 12:35:59
Works as intended
Shawn B
2025-06-25 12:54:56
Even after validating in the QA section if thes is clear or yellow, I was assured it was clear. Thes is by no means clear. This is unpigmented resin. Is is completely different than a clear resin.2nd bottle will not even print. It is twice as thick as first bottle. Even after preheating my buildplate stutters trying to get to the bottom of the vat and all print turn to jello because it isn't going down far enough. It is also a nasty mess to clean up. It has some reaction with ipa that turns it into a glue like gooey mess.
KS
2025-06-10 14:24:28
This resin is very easy to work with in contrary to some comments and video clips found online. I use Chitubox and the profiles available from the Siraya Tech site are very helpful. The pictures show some prints for my FDM printer and I'm quite satisfied with the result. Now hoping its HDT property is up to it claims.
Vladimir Yonkov
2025-06-03 16:48:22
Perfect brand and perfect quality. High detail printing with that Resin.also its High temperature durable good for moulds
Marcin
2025-05-13 17:29:18
Jestem zadowolony z żywicy tylko trzeba ją dobrze wymieszać
Cliente
2025-05-09 21:06:28
Utilizzo questa resina per la costruzione di esche artificiali o per creare stampi in gomma.La resina risulta facile da lavorare ma è anche molto resistente.Consiglio di seguire le indicazioni che trovate sul sito Siraya. I settaggi per l'esposizione sono plug'n'play ma suggerisco sempre una calibrazione della resina. Sul sito trovate anche istruzioni per i tempi di Wash and Cure.La uso su una ELEGOO Saturn 4 Ultra senza problemi.
Daniel S.
2025-05-05 16:55:20
good
Customer
2025-04-30 21:11:46
I used the 80% Siraya Tech Sculpt High-Temp Resin with 20% white Tough Resin I had on hand to make new sockets for a tube preamp I am refurbishing. . I did some tests with 100% Sculpt but when I did my offline temperature tests, it withstood the heat but the thermal shock from getting hot and cold quickly caused the thin areas to crack. By mixing with some tough resin, I was able to make a part that has held up to the ~100C temps without cracking. The pictures show the before and after the the tube/socket replacement. I will definitely be using Siraya Tech Sculpt High-Temp resin for future projects. By the way, it printed flawlessly! (I use a heater inside the chamber set at 90F.)
Alexandre Masse
2025-04-29 12:48:16
Sculpt ultra is one of the most amazing resins I've used and really shows the trickle down of material science to consumer level printers. It barely absorbs any water or solvents and is incredibly rigid. It's very ceramic like in many ways, probably because it IS filled with ceramic particles. It's a bit difficult to print, bed needs to be leveled just right and more importantly, because the resin is so opaque, the z-height needs to be very small to not have bed adhesion issues. I had a ton of issues until I realized that was my problem. Whenever I level my bed, I then set the zero a couple steps down and everything is good. The prints come out very smooth and because it's so brittle, the supports come off the cleanest of any resin I've tried. It also means you can't drop your prints as it will shatter like glass. Highly recommend for specialized use cases where you need high chemical, wear and heat resistance.
John Fitzgerald
2025-04-17 09:52:10
Fantastic Resin
theSLAchannel
2025-04-09 20:02:50
I bought this primarily to make molds to cast urethane parts in, and it does a great job at that. But I've also printed some tiny objects just to see what it- and my printer- could do.The chair and cubes have no post processing other than support removal. The large cube is 6mm. The resin prints slightly oversize, cube ended up being 6.18mm, but it is consistently the same.Printed on an Anycubic Photon. 100 sec first layers, 15 sec exposure.**UPDATE**I've continued to use this, and have been VERY impressed by the results. Excellent details. A great resin at any price, but an absolute STEAL at this price.
Timothy P.
2025-04-07 12:12:13
Printed perfectly fine! Haven't had a chance to test the heat resistance yet. The parts are accurate and clean! One thing I did notice is the color isn't clear it's more of clear yellow, a very light yellow yet still yellow. I even mixed some with some abs like Grey I had laying around to see if it would help the heat resistance with that as well, gotta day had no issues printing the mix! Will buy again!
Jonathon Hernandez
2025-03-08 14:39:21
I printed this hose adaptor for our projects. It worked out great. I feels like ceramic and breaks like ceramic. Just be careful when sanding it you don’t want to breath the dust in. Worth the buy
Great stuff. Easy to work yet.
2025-02-26 17:28:02
Works as intended
Shawn B
2025-01-31 18:39:13
Even after validating in the QA section if thes is clear or yellow, I was assured it was clear. Thes is by no means clear. This is unpigmented resin. Is is completely different than a clear resin.2nd bottle will not even print. It is twice as thick as first bottle. Even after preheating my buildplate stutters trying to get to the bottom of the vat and all print turn to jello because it isn't going down far enough. It is also a nasty mess to clean up. It has some reaction with ipa that turns it into a glue like gooey mess.
KS
2025-01-24 21:32:50
This resin is very easy to work with in contrary to some comments and video clips found online. I use Chitubox and the profiles available from the Siraya Tech site are very helpful. The pictures show some prints for my FDM printer and I'm quite satisfied with the result. Now hoping its HDT property is up to it claims.
Vladimir Yonkov
2024-12-16 11:30:27
Perfect brand and perfect quality. High detail printing with that Resin.also its High temperature durable good for moulds
Marcin
2024-12-09 11:43:34
Jestem zadowolony z żywicy tylko trzeba ją dobrze wymieszać
Cliente
2024-11-30 20:59:04
Utilizzo questa resina per la costruzione di esche artificiali o per creare stampi in gomma.La resina risulta facile da lavorare ma è anche molto resistente.Consiglio di seguire le indicazioni che trovate sul sito Siraya. I settaggi per l'esposizione sono plug'n'play ma suggerisco sempre una calibrazione della resina. Sul sito trovate anche istruzioni per i tempi di Wash and Cure.La uso su una ELEGOO Saturn 4 Ultra senza problemi.
Daniel S.
2024-11-16 18:53:17
good
Recommended Products