Your cart is empty.
Your cart is empty.Product Description
-
SpeTool Flush Trim Router Bit
Spiral design provide better chip evacuation , SpeTool offer upcut ,downcut and compression cut
-
SpeTool Flush Trim Bit with TAC coated
TAC produces cutting results of the highest quality and longevity, increase up to 2.5 life times compared to uncoated bits
-
SpeTool Flush Trim Bit
The Flush Trim Router Bit is fitted with high quality bearings that feature two separate ball bearing roller guides at the tip.
-
SpeTool Flush Trim Bit
Solid carbide Flush Trim Router Bit significantly outperform and excel in conventional flush milling cutters
SpeTool Flush Trim Router Bit
Efficiency
The high cutting performance of SpeTool Flush Trim Router Bit ensures faster and more efficient material removal and clean cuts.
Ball-bearing
The Flush Trim Router Bit's double ball bearings facilitate routing according to templates and ensure a smooth cut.
Clean Surfacing
Sharp and smooth flute will leave an excellent cutting finish
Different sizes
Different sizes of Flush Trim Router Bits meet different needs in woodworking and finishing projects.
Matt & Megan
2025-08-25 18:10:10
Used this but for a project and it even produced a very clean edge on plywood.
Shivani
2025-08-19 13:43:20
My most frequently used bit! Just ordered for the second time after ruining the first bit cutting acrylic, which melted into the bearings. I use this bit way more often than any other pattern bit, it gives the least tear out and kickback out of all my bits. Cuts are super smooth, and the bit almost never leaves burn marks. It’s definitely the bit I use if I have to route across end grain, and I’ve done patterns across end grain on 3/4†and 1†thick woods including oak, ebony, maple, tamarind, mahogany, and ash.
M/G
2025-08-08 15:58:18
So these work really well for final trimming if you've already roughed out a cut or only have to trim up a piece with a pattern. For full pattern cutting these hold up decent, but discolor/dull with 3/4" MDF after 100' or so.
Dmoney
2025-07-03 18:56:59
I've cut all types of hardwood for a Texas shaped template. I've made 20 so far from walnut, purple heart and other exotics and this handles it well if you only leave 1/8" of material for it to cut. If you can't do this I'd suggest a thicker diameter bit.
Roscoe Flippinbitz
2025-06-30 11:04:49
Good value good bit
Customer
2025-06-19 21:11:08
This is the first time buying one of these spiral cut flush trim bits and I’m happy to have them in my collection. They cut so much smother and blow-outs are almost absent and less severe than the fluted trim bits.
K
2025-05-18 12:33:35
Works great for the price
Elaine
2025-05-10 10:23:30
The bit broke the first time I used it. I returned the broken bit for a new one to try again. The bit broke again on the first use.I have other Amana bits that work fine.
Prisciliano Antonio Castelan fortuna
2025-04-15 15:55:40
Llegaron bien y todo el unico detalle fue que llego una que no era
otkar
2025-03-12 13:07:03
This bit is very well balanced. I gave it a test on a piece of walnut and and it was super sharp that I did not need to press hard against the template and it produced nice shavings not dust. . I've never seen a smooth finished wood surface like that. I am not sure how durable it will be but I am really impressed by the quality. Carbide is a brittle material especially on 1/4" bit so I will try to handle it delicately and be careful when feeding my work especially when starting at corners.
Douglas Y.
2025-03-08 16:51:37
I build guitars and use these for trimming out necks. They work very well and seem to last quite a while. Only 4 stars because one broke off flush at the collet when trimming 4mm vinyl flooring I had glued to my work bench top….never had a problem before on hard maple, ect. Weird….must have been a bad one. Never had any other ossues.
Customer
2025-02-15 16:18:23
Have used a lot, it works great
Karen Taraska-Alcock
2024-12-23 11:56:15
Came on time as described.
Recommended Products
$35.85
$ 17 .99 $17.99