Your cart is empty.
Your cart is empty.Product Description
Maria
2025-09-02 18:50:02
I created a Halloween animatronic using a wiper motor. I plugged this sensor into the wiper motor and then to a 12v power adapter. The result is my animatronic goes off when the sensor detects motion. Super easy to install and works like a charm.
Jrbufny
2025-07-14 12:26:34
My DVR for a security camera was detecting too much as motion. Was also recording when lighting changed. I only wanted to record when someone was there. PIR sensor added near camera - placed at 12v supply to camera. Uses same plug and jack that camera has so very easy install. I did have to take the camera off a 4 way power splitter and put it on its own power supply. Found a review by someone else that mentioned something about needing a dedicated ground. When on the four way splitter the switch stayed on. The set screw adjustment inside the switch housing works - tried from lowest - just a few seconds to highest - several minutes. Using indoors - not waterproof.
Customer
2025-07-08 12:42:06
Dead on arrival, stuck at "on", no detection at all. Complete waste of time and money. DO NOT buy this thing!
jeff
2025-06-24 18:20:36
It worked fine out of package with the preset default delay within the specs. I purchased this because it was stated as adjustable delay from 2 seconds to whatever, I forget, but out of package it was 20 seconds. When I popped the back off to turn the pot down closer to the 2 second interval the delay bounced all over the place randomly. I would say it is just cheap and even though it says it is adjustable, to not mess with it. As is, it is what you get and it probably would have worked. Four stars would have been generous, but three is fair. The product works but they don't really expect you to adjust it. I'll take away the generous star because if you advertise the adjustment it ought to work. The next week I purchased the sensky, it cost a couple dollars more, but it did come in a retail package, rather than in plain baggy. I would guess it was probably a "second" since there are many variations listed on amazon and many prices. Most products have the same description with only slight differences in the specs. One of the products does say to not set at minimum delay because it will malfunction, so I gave one star back because it might have been this product, so I'll take fault and not return. It still works and i'll rebuild it later with a better part. I'm not knocking this product, but i did expect a little better out of this since supernight is billed as the bestselling on amazon in many of the LED components. It works, but just wasn't reliable for adjustment. If you want a simple motion detector switch to fire up an LED project and at the pricepoint by all means, buy this with out hesitation. If you want something that has reliable delay spend a little more, but read the reviews and compare those to what the specs advertise before purchasing.
Jonathan W.
2025-04-16 14:02:35
I'm using this to run the led strips I install in a cabinet and while I've only been using it for about a weeek, it's been working perfectly. It only turns on when it detects movement about 2-3 feet away and turns off if I walk away. If I open the door quickly it'll turn on the lights but slowly it won't. As soon as I step in front of the cabinet though it turns right on. So far very happy with it
deal finder
2025-03-15 20:23:10
I've had this installed on some LED's that illuminate a stairway down to my basement for a couple months now. It works really well.
CMYK Josh
2025-02-25 10:42:38
A cheap, simple way to add motion sensing to LED lighting. I plugged it in, stuck it on the wall, and when I walk into the closet, the lights come on. It doesn't get much simpler. Now, this is DC and it's plugged to work with LED light strips and the sort. If that's what you're looking for, you're in luck. I have it set in a way that it activates when a door is opened so I don't have a good range estimate. It automatically shuts the lights off after 15-16 seconds of no motion. Neither delay nor proximity are adjustable. It's really just plug-and-play and that's fine for my needs.
Mark Jones
2025-02-10 17:05:01
These seem to do the job with limits. When powering over 10 meters this motion sensor caused a pulsing of the lights. It's weird and made me wonder if I was seeing things.I had one fail to turn off/timeout while I was trying to test the timeout duration. I left the case off to adjust the timeout but the switch didn't work properly without the case.When I only want a
Recommended Products