Your cart is empty.
Your cart is empty.
Ximimark 4Pcs USB 2.0 to TTL UART 5PIN Module Serial Converter CP2102 STC PRGMR Free CableMPU-6050 MPU6050 6-axis Accelerometer Gyroscope Sensor
Stable and reliable chipset CP2102; Supports full range of STC single-chip microcomputer with output voltage 3.3V and 5V; Supports Windows 98SE, 2000, XP, Vista, Window7, Mac OS 9, Mac OS X & Linux 2.40.
Baud rates: 300 bps to 1.5 Mbps, support for the highest baud rate up to 115200 bps.
Standard USB type A male and TTL 5pin connector. 5pins for 3.3V, RST, TXD, RXD, GND & 5V; Connect MCU easily to your computer!
With indicator LEDs: power indicator, the indicator data reception, data transmission indicator. After the driver is correctly installed, the status indicator will be on, the sending and receiving indicators will flash when communicating, and the higher baud rate, the lower brightness.
Application: It is designed to be used for USB to TTL electronic projects. Package included:3* USB To TTL 5 pin UART STC Downloader Module + 3*Jumper Wires
Package included：Ximimark 4Pcs USB 2.0 to TTL UART 5PIN Module Serial Converter CP2102 STC PRGMR Free CableMPU-6050 MPU6050 6-axis Accelerometer Gyroscope Sensor
Thank you very much for shopping in our store. Please feel free to contact us if you have any questions.
Description:
Exquisite workmanship and high quality. Welcome to buy
Size :as shown
Feature : fashion
Style : as shown
100% brand-new high quality
Note:
We are very grateful to all customers for their suggestions on improving sales. If you have any dissatisfaction, please contact us to find the best possible solution. Thank you!
Package included:
Ximimark 4Pcs USB 2.0 to TTL UART 5PIN Module Serial Converter CP2102 STC PRGMR Free CableMPU-6050 MPU6050 6-axis Accelerometer Gyroscope Sensor
Mitch
2025-08-31 12:19:34
Was easy to swap out some bad boards in my Baofeng programming cables with minimal work. Product had enough solder on it that I just needed to reheat the spot and add the cable in. No issues with drivers or software. Would recommend.FYI, for step by step instructions, search for "Miklor Build your Own Programming Cable" and this page will show you all the correct pinouts for the cable.
shred
2025-07-02 10:51:48
1 star deduction because jumper wires are too short.
True Laser Cutting, LLC
2025-04-09 18:00:25
Works with all of the Nextion screens I have used, so no more microSD card needed. When setting up: red to 5v, black to ground, blue to Rxd, Yellow to Txd (yes the blue and yellow wires are "swapped" from the output of the screen).Also I needed to download the driver from the manufacturer of the chip, very easy just google : CP210x Universal Windows Driver.Good product, also somehow the shrink wrap just makes it feel more secure which is good.... IDK.
Fuzzhao
2025-04-02 12:23:04
These are supposed to be CP2102 chips from Silabs.Most of them work fine, but some of them seem to have the CP2102 chips flashed with custom firmware and they won't work, they show up as some modem or printer or otherwise show up as a device incompatible with Silabs drivers.I suspect some of these chips are recycled chips, desoldered from e-waste
Eat my crocks
2025-03-17 14:36:34
I give this a 4 star review because it works as intended. But it doesn’t do everything I wanted.I used it for an atmega 328 project but I am left needing to reset manually for uploading arduino sketches. Over all not bad. Worth the money
Jim B.
2025-02-25 14:36:07
I did not received four set of free cables for these four board as indicted above.
Customer
2025-01-05 21:02:18
The device works well when connected to USB 2.0 ports, with about 4 SerialPort error events per 1 Million characters, but regularly crashes when connected via a USB 3.0 splitter after a random number of characters, usually with SerialPort.BytesToRead > 0 and system error on SerialPort.GetAvailable. Device has to be physically disconnected from port to re-initialize.
Edward Plese
2024-12-29 11:14:16
The quality control for these are awful and 0 of the 4 I received worked.One of the 4 was completely dead. When plugging into USB none of the lights came on. The other 3 weren't recognized by Linux as a CP2102 USB to UART because they are programmed with the wrong USB VID and PID. It might work with some changes to udev but I expect these to simply be plug and play in any Linux system.The header pins were all soldered in at an angle. Functionally this would work but it just looks bad and sloppy. One of the 4 was missing one of the pins.
javier h
2024-12-20 11:01:54
Funciona bien como programador de radios de comunicacion kenwood y baofen
Recommended Products
