Your cart is empty.
Your cart is empty.No one enjoys scrubbing off stubborn, dried-up bug guts after a long road trip. That’s where the Bugflector II comes in. The high-profile wrap-around design provides maximum protection from all bugs, big and small, while its off-the-hood design allows for easy cleaning and waxing. Made from durable impact-resistant acrylic, the Bugflector II can stand up to everything from car washes and bugs to the wear and tear of daily driving or going off-road. Custom-molded to fit your vehicle’s exact year, make, and model and contoured to fit the curves of your hood. Available in dark smoke finish and proudly made in the USA with global materials
Ericpdadof3
2025-08-09 16:16:47
I received the bug shield in the factory box, which was well-protected. Installation was a breeze, make sure you mark which factory tabs come off so you don't pull out the wrong ones. Highly recommend to anyone with a truck! Looks great too.
singleJIM
2025-06-27 12:36:45
Looks good but requested more clips. The middle four went on easily. The outside clip on each side was too long. They said it was correct for my 2024 Ram 1500 Bighorn. I have requested more clips but have not received them yet.
Massimiliano Calcagno
2025-06-23 18:27:39
Installed this today. Looks great on my Ram Big Horn and the quality seems good. As many of the reviews stated though I did have some issues with the “hardware†provided for the install. Install was easy enough but I had to run to the auto parts store and replace two of the grommets. All and all I am happy with the way this looks on my truck and aside having to replace the parts provided the install was easy enough.
Dave E
2025-05-07 18:31:38
The unit fits well but the factory fasteners broke when I removed them with a fastener removal tool, so be sure you're only removing the ones specified in the instructions. The broken tabs are rattling around inside my hood but should fall out by themselves at some point. This unit has a pretty tight fit and the supplied plastic screw anchors could be better. They're thin and have a fine thread so they can be tricky to tighten. You might also have to adjust the hood bump stops. My hood was difficult to close after installation so I backed the bumpers down about a half turn.
Joe
2025-05-03 12:06:05
I sent the following message to Auto Ventshade. I have not heard a peep. As I received no response, I purchased a pushpin kit so I was able to install the deflector. It was no easy task. The majority of the slots on the deflector did not line up with the hood.I am writing to complain about the AVS Bugflector Hood Shield that I recently purchased. I tried to install the shield according to the instructions, but the push pins that were included were too long to fit in the hood. I tried to trim the push pins, but they were still too long. I even tried to use different push pins that I had on hand, but none of them were the right size.In addition to the push pins being too long, the package was also short 14 push pins. I needed 20 push pins to install the shield, but the package only included 6.I am very disappointed with this product. I have been a loyal Auto Ventshade customer for many years, and I have never had a problem with their products before. However, this product is clearly defective.I would like you to send me a new package of push pins that are the correct size. I would also like you to send me a refund for the 14 push pins that were missing from the original package.I hope that you will take this matter seriously. I am a very satisfied customer with your products, and I would like to continue to be a customer. However, I cannot do that if I am not able to install the Bugflector Hood Shield properly.Thank you for your time and attention to this matter.
ANJ
2025-04-07 10:15:40
The smoke Bugflector 2 looks great on my 2022 Ram 1500 5th gen. Installation is horrendous. The clips packaged with the deflector are too big and don’t work. Here is what I did: I bought the GOOACC 635Pcs Car Push Retainer Clips for under $20. I used the clip shown in the photo with this review to attach the deflector to the body in the existing holes (6 of them). In other words, I did not sandwich the rubber seal and the deflector under the clip, as clip I used is too small for that. Then, I used 3M double sided advanced auto tape to attach the rubber seal to the deflector at the clip points. It’s been on about 10 minutes, so I can’t vouch for longevity, but all seems okay. It’s a 2 person install.
Brent Schuler
2025-03-13 18:20:45
I installed this on my 2021 Ram 1500. It fit perfectly. I only removed the factory clips from the hood seal where the deflector holes lined up and yes they will break, so I recommend only removing the necessary ones. Also when installing the supplied push pins I nipped about3/16†off the pointed end so they wouldn’t bottom out. You have to really push the outside part of the push pin to compress the weatherstrip rubber in order to screw the center piece in. It’s is possible and would be easier in warmer temperatures. The people that say they don’t work are probably not mechanically inclined. It took me about 20 minutes to install by myself, as others have said a helper would speed up the install.
WXman
2025-03-10 18:49:35
The Bugflector II fits my truck reasonably well. Not perfect, but pretty close. Looks nice on the truck. My goal is to keep rock chips off the edge of the hood and this should do the trick. However, be advised that you need to buy hardware before you start this installation. On the 2022 Ram 1500, double sided tape is not used. Instead, they give you six screw-insert type plastic rivets. I found that these rivets were a joke. They would not thread correctly in hand apart from the installation, much less thread correctly when I tried to insert them into the hood. Absolute garbage. Thankfully, I had an inventory of various plastic rivets in my toolbox and I was able to find a few that will hold the Bugflector onto the hood until a more permanent solution can be found. Since hardware is the key to any item like this, I have to give 3-stars.
michael savery
2025-02-24 18:11:54
This Hood Deflector does NOT properly fit. It is NOT contoured properly! I contacted the manufacturer & while they initially acknowledged my email, they did NOT respond again. It's been over 1 week, which is unacceptable. A warranty issue should be dealt with immediately. I will continue to pursue to have my Hood Deflector replaced or obtain a full refund. So far, the warranty service is non-existant. If that changes, I will gladly update this review.
Jocelyn Raymond
2025-02-23 14:35:21
Pare pierres et moustiques
Frenchie
2025-02-10 13:48:14
Light strip stopped working after a few months. My question is that I'd like to know if I can get another Light strip to replace the one that quit working. Wish there was a way to contact the seller so I could get another Light strip to replace it. Other than the light stop working. It looks great when the light is working.
Byron Y.
2025-02-05 15:17:07
Looks great and easy to install
Derek Y
2024-12-30 11:15:30
The fit was good and installation was pretty straight forward on a 2020 Ram ORP .. The only slight problem was the little oval AVS sticker fell off after a couple of weeks but that just saved me the trouble of removing it myself.
Recommended Products
$126.99
$ 61 .99 $61.99
$104.95
$ 49 .99 $49.99