Your cart is empty.
Your cart is empty. Quick and Easy
This cost-effective pulley puller will help you get your new MINI supercharger pulley on faster. With our tool, you will be able to remove the stock press fit pulley safely, without removing the tensioner. Time is money and this puller will save you both.
Tough as Nails
The puller body is made of heat treated carbon steel and has a tooth profile to match the OEM pulley exactly. The center screw is grade 8 quality. Having a pulley party? Our puller will not bend during normal use, and will last for many pulls.
BARLOW
2025-09-03 20:01:01
Don't mess around with the other puller on the market it is made of aluminum and when I used it two of the three supplied bolts ripped the threads right out.The cra e speed tool is made from high carbon steel and worked like a dream. Learn from my mistake the aluminum one cost me a week of downtime waiting for the cra e speed tool to get here.
Michael Monio
2025-08-13 17:24:14
Have previously removed press fit supercharger pulleys on Minis with a cutoff wheel. Highly recommend this product! Extremely easy to use and manufactured of high quality materials. Worth every penny!
Joe Grimsley
2025-06-30 18:56:31
Works..very well! They give you some lube with this kit...USE IT! Also buy a chain vice grip..it helps with the tool so it doesn’t slip..that pulley is on super tight. But it’s pricy for a one time use...but there is NO other way to get that pulley off a mini without risking damage to the SC.
Isaac Hall
2025-06-04 18:10:18
The package arrived a day early. I used this and had the original pulley of my original supercharger in 10-15 minutes. Don’t waste your time trying to buy and use a cheaper puller for your supercharger!!!
Texas True
2025-05-23 11:13:33
I Removed pulley on bench NOT on engine.... would be a tight squeeze inside engine compartment. Force required deformed bolt nose... had to grind tip to remove... all good though as it was a one time use tool for me
Doug
2025-04-03 10:10:06
Used this to change the supercharger pulley on my R53 Mini Cooper S and it worked great!! No issues at all.
Zerin
2025-03-21 17:19:47
R53's with the JCW package may have one of two different size pulleys. A larger one or smaller one. (duh?) But I had rented a special JCW pulley puller for my JCW but it was too small! But this one from cravenspeed I was able to pull it.... with a bit of slack. Even so, no issues with this one! Good buy, good price.
Micheal Dennison
2025-02-11 13:59:00
This tool is used to remove the factory supercharger pulley from a Mini Cooper S. It is very expensive, but necessary for this job. A standard pulley puller does not really fit on this pulley and I have heard horror stories of people damaging the pulley and having to grind it off. So, in my book, this is a must have. It fits perfectly on the old pulley and pulls it off very easily. One small complaint (about the job, not the product) is that you can only go so far when pulling it off before it hits the frame. It is not a big deal, you just have to carefully hammer it off the rest of the way. There just isnt enough room for it, so I am not blaming the part.One important note though, this does not fit on a reduction pully, only the factory supercharger pulley. (and for that matter on none of the other pulley either)
Simon Fenn
2025-02-07 13:02:35
Must have for removing stock r53 pulley. Definitly worth the money, and after your done with it you can always re sell it to forums.Get chain vice grips and wrap it around the puller. Makes it easier
Kristian Molloy
2025-01-04 17:35:18
The tool worked fabulously, but a bolt at the end of the supercharger snout should be screwed into it or damage to the snout will occur.
Recommended Products
$19.95
$ 8 .99 $8.99