Your cart is empty.
Your cart is empty.Dracaena PCIe Riser for Crypto Mining 3 power options: 6-Pin PCIe, MOLEX, or SATA. LED indicator shows the power status of the board Coil added to prevent electromagnetic wave interference 60cm USB 3.0 riser cable enabling flexibility in the placement of your PCI-E devices. No drivers needed. PCIe 1x to 16x extension cables with multi-layer shields to prevent signal loss (up to 3 meters) Board dimensions: 13cm x 3cm x 1.2cm Please make sure the computer is powered off when you plug in or out the PCIe extension cable. The USB cables are specially made. Please do not replace them with other cables. Since there are three power options on the card, the four mounting holes on the card locate a little differently from the cards with only one power option. Refer to the pictures for the location details. 6x PCI-E riser board 6x PCI-E 1X adapter card 6x 60cm USB 3.0 riser cable Note: 6pin to 15-pin SATA Power Cable are not included
Noah Delfel
2025-08-20 11:59:24
Purchased this to power a SAS expander in a DIY disk shelf for Unraid. Works perfectly for my needs! Multiple ways of providing power is great; would always recommend using 6-pin power if possible, but for less demanding devices SATA power or molex should be just fine in theory
Waren
2025-08-09 19:34:07
Takes a little work to figure out how to use on certain cards but work and are of good quality. Would buy again...
Mike Solo
2025-07-25 17:07:29
So I’ve had a 3070ti sitting around for a couple months and finally put it to use. Since I had a itx motherboard I only had one pcie slot. Ended up buying this and a m.2 to pcie adapter, connecting it to the back of my motherboard. (Aorus b550i). I did have to buy a psu separately but after putting everything together, it turned on with no issues. I’ll report back if an issue arises but everything seems to be working just right for now.
K. G. Fox
2025-06-28 14:13:10
Needed an additional PCIE slot for a custom OpnSense build. My converted PC only had one, all the rest were x1 slots. (4 of them). This fit the bill perfectly. I installed my 4 port NIC in to the existing slot on the MB, and put the video card on this jumper. I routed it to the bottom of the box, as I had some decent empty slots in the back plate. This allowed the card to sit on the bottom of the case. No drivers necessary, worked out of the box.Only thing I wish were included is some kind of mounting option. The card is pretty light weight, so the screw to the back plate is probably sufficient, but an adhesive mounted standoff for the card would have made it more secure.
Gilbert Chun
2025-05-27 12:24:03
My capacitor broke off when opening the baggy but when I emailed no questions where asked and they gave me a replacement, they went as far as giving me an extra one for coming to them with the problem. This was fast and precise and their pcie are high quality. Definitely buying more for my next 3 mining rigs!
li li
2025-05-26 17:07:27
I bought this PCIE riser specifically to mine crypto and it works extremely well. It’s was simple to set up and was in pretty good quality. I’l definitely buy more as I expand my rigs.
Brandon Hardin
2025-05-16 09:07:49
Great value, and not just for the money. Always use 6 pins to power your risers. Unless you have the money (and stock) to not care about a bricked card. These are top of the line and I will continue to purchase these. Ive built a few rigs and all my cards are on these or an equivalent.
Vlad Shimansky
2025-05-14 10:33:47
These riser cables are great. However I had two of them arrive defective. I contacted Dracaena (the seller) and they got back to me literally in less than a minute offering to send me replacements. I wish more companies had such customer service. Won't hesitate to purchase from them again.
Max Powers
2025-05-04 18:06:32
Set them up and plugged in cards and works.
Carlos C.
2025-04-24 14:08:54
Funcionan sumamente bien, lo único incomodo es que el puerto sata lo tienen en un lateral en vez de en el frente o atras, lo que dificulta usar menos cables sata si vas a conectar más de una tarjeta.
Matt C.
2025-03-23 17:45:29
Sometimes when testing computer hardware, you need to test graphics cards. If you have a testing motherboard hooked up to a power supply on a table or bench, sometimes the GPUs can be hard to stand upright or they have a decency to “lift†themselves out of the slot.This adapter, even though it was designed to be used in a *coin mining environment works great. Simply connect the adapter to the PCIe connector on the GPU, apply a power connector to the adapter, plug the PCIe x1 connector in your motherboard and off you go. The USB 3 cable is the link between the motherboard adapter and the PCIe slot adapter.Note: don’t use multiple power connectors plugged into the adapter. You may overload the power delivery circuitry and make it release magic smoke. I haven’t tested this, but more just a friendly heads up.Note that this will not power a GPU solely from the PCIe slot, you’ll need to plug another connector into the GPU power connector. It may even fail if you solely ran the GPU from the power the slot provides. I tested it with a bus powered GPU with the adapter connected via the male SATA connector and it was peachy.Recommended, but don’t push it too hard.
Alex
2024-12-25 18:22:20
Great project, performed as described.
Ariadna Rodriguez
2024-12-12 14:58:57
esta bueno el producto, pero solo me llego 1
Recommended Products
